Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
INSTALLATION MANUAL
2730CIK Clean Install Kit
Use with Valor LT2 2700 Heater Models ONLY (series K or later)
DANGER
!
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and must be
installed for the protection of children and other at-risk
individuals.
The 2730 Clean Installation Kit installs at the time of
framing the appliance. Wall fi nishes are then applied
and butted directly up to the outer frame.
Dimensions
4009510-01
©2023, Miles Industries Ltd.
LT2 Series
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Depth
1-1/4"
[31.75 mm]
51" [1296 mm]
INSTALLER: Leave this
manual with the appliance.
CONSUMER: Retain this
manual for future reference.
Note: This kit must be
installed or serviced by a
qualified installer, service
agency or gas supplier. These
instructions are to be used
in conjunction with the main
installation instructions
for the above listed heater
model.
This kit is not intended to and cannot be installed with
any other trim.
See appliance installation manual for more
information about finishing around this kit.
2700K engine
Left hand
door
Cover
plate
Barrier
screen
Overview
Right
hand door
CIK assembly
Publicité
Manuels Connexes pour Valor LT2 Serie
Sommaire des Matières pour Valor LT2 Serie
- Page 1 INSTALLATION MANUAL LT2 Series 2730CIK Clean Install Kit Use with Valor LT2 2700 Heater Models ONLY (series K or later) DANGER INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this HOT GLASS WILL manual for future reference. CAUSE BURNS.
- Page 2 Installation 3. Slide CIK frame into the opening as shown, pushing it as far in as it will travel. The 2730CIK kit is intended to be installed at the time of framing, and before installing the wall fi nish. With the 2700 engine installed and in place, you can proceed with the following steps to install the 2730CIK kit.
- Page 3 5. Once wall fi nishing is complete, place cover plate in 7. Insert the left hand door top hinge pin in the hole at the bottom of the opening. It will rest on the sup- the top of the CIK frame (a), then the bottom hinge ports at the bottom corners of the opening.
- Page 4 Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication. Designed and Manufactured by / for Miles Industries Ltd. 190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1 Tel. 604-984-3496 Fax 604-984-0246 www.valorfi replaces.com...
- Page 5 GUIDE D’INSTALLATION Série LT2 Encadrement 2730CIK Utilisez sur les foyers Valor LT2 2700K SEULEMENT DANGER INSTALLATEUR : Laissez cette notice avec l’appareil. CONSOMMATEUR : Conservez cette notice pour consultation VITRE CHAUDE - RISQUE ultérieure. DE BRÛLURES. NOTE : Ce kit doit être installé...
- Page 6 Installation 3. Insérez le cadre dans l’ouverture et poussez le jusqu’à ce qu’il touche la caisse. Le 2730CIK est conçu pour être installé avant la fi nition du mur. Une fois les pièces intérieures du foyer en place, installez l’encadrement comme suit : 1.
- Page 7 5. Posez le couvercle en bas sur les supports latéraux 7. Placez la porte latérale en insérant d’abord sa à chaque coin du cadre. cheville du haut (a) puis sa cheville du bas (b). Note : L’encoche arrondie à chaque extrémité du Tournez la porte vers l’arrière (c).
- Page 8 Parce que nous favorisons une politique de développement continu, certains détails de la présente publication peuvent varier. Conçue et fabriquée par / pour Miles Industries Ltd. 190 – 2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1 Tél. 604-984-3496 Téléc. 604-984-0246 www.fr.valorfi replaces.com...