Benning MM 8 Notice D'emploi page 21

9.3­ Battery­change
Before­opening­the­BENNING­MM­8/­9/­0­make­quite­sure­that

it­is­voltage­free!­Electrical danger!
The BENNING MM 8 is supplied by two 1.5-V micro batteries, the
B ENNING MM 9/ 10 is supplied by a fitted 9 V block battery.
A battery change (­see Figure 11) is required, if in the display  the battery
symbol  appears.
Proceed as follows to replace the batteries:
- D isconnect the safety measuring cables from the measuring circuit.
- D isconnect
B ENNING MM 8/ 9/ 10.
- T urn the rotary switch  to the switch setting "OFF".
- R emove the rubber protection frame M from the BENNING MM 8/ 9/ 10.
- L ay the BENNING MM 8/ 9/ 10 face down and release the two slot screws
of the battery compartment cover.
- L ift the battery compartment lid (­in the housing recess area) from the bottom
section.
- L ift the discharged battery/ batteries from the battery compartment and
carefully disconnect the battery supply lines (­BENNING MM 9/ 10) from the
battery.
- T he new batteries have to be connected to the battery supply lines, and
arrange these such that they are not crushed between the housing parts
(­BENNING MM 9/ 10). Place the battery/batteries into the battery compart-
ment provided for this purpose.
- P lace the battery compartment cover onto the bottom part and tighten the
screws.
- I nsert the BENNING MM 8/ 9/ 10 into the rubber protection frame .
see figure 11:
Make­ your­ contribution­ to­ environmental­ protection!­ Do­ not­
dispose­ of­ discharged­ batteries­ in the household garbage.

Instead,­ take­ them­ to­ a­ collecting­ point­ for­ discharged­
batteries­ and­ special­ waste­ material.­ Please­ inform­ yourself
in­your­community.
9.4­ Fuse­replacement­(­BENNING MM 9/ 10)
Before­opening­the­BENNING­MM­9/­0­make­quite­sure­that it

is­voltage­free!­Electrical danger!
The BENNING MM 9/ 10 is protected against overload conditions by means of
a fitted fuse (­G melt insert) 10 A (­see Figure 12)
Proceed as follows to replace the fuse:
- Disconnect the safety measuring cables from the measuring circuit.
- Disconnect the safety measuring cables from the BENNING MM 9/10/.
- Turn the rotary switch  to the switch setting "OFF".
- Remove the rubber protection frame  from the BENNING MM 9/ 10.
- L ay the BENNING MM 9/ 10 face down and release the four slot screws of
the housing bottom.
Do­ not­ undo­ any­ screws­ on­ the­ printed­ circuit­ of­ the­ ­

­ B ENNING­MM­9/­0!
- L ift up the housing bottom in the lower section and remove the same at the
top from the front section.
- L ift one end of the defective fuse from the fuse holder.
- F ully push the defective fuse out of the fuse holder.
- I nsert a new fuse which has the same current rating, disconnecting charac-
teristic and dimensions.
- M ake sure that the new fuse is seated centred in the holder.
- O rder the battery supply lines such that they are not crushed between the
housing parts.
- E ngage the front end on the housing bottom and fit the three screws.
- Insert the BENNING MM 9/ 10 into the rubber protection frame .
see figure 12:
11/ 2006
Electrical­danger!
the two
Battery change
Electrical­danger!
Fuse replacement
­ B ENNING­MM­8/­9/­10­
safety measuring
in­ the­ household­ garbage.­

that­
cables from
yourself­
that­it­
the
9