Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
When deciding where to install the transmitter
(measuring location), take care that the ambient
conditions given in Section «5. Technical Data»,
are not exceeded.
Make the cut-out or drill the holes in the item onto which the
transmitter is to be mounted according to the corresponding
drilling and cut-out diagram given in Table 1.
7. Adjusting the angle
Angular position transmitters of the KINAX WT 711 range do
not require a mechanical zero position mark (however, this
is made if required by the customer, see Fig. 5).
Fig. 5. Zero position mark.
Left:
for rotation transmitters with the range of 0 to ...
Right:
for rotation transmitters with V characteristic ranges.
During installation the shaft of the transmitter can be coupled
to the object to be measured in any position. Adjust the shaft
angle as follows with the 2W2 confi guration software:
1. Remove the plastic cover from the housing. Remove the
rubber cover (3) to gain access the programming connector
(4) (see section "8.1 Connecting transmitter" and Fig. 8).
Connect the KINAX WT 711 to the programming device
according to Fig. 6. Start the 2W2 confi guration softwa-
re. If necessary, confi gure the device with the required
measuring range data.
The angular position transmitter must only be
programmed outside of the Ex area!
Those max. angular speed of the wave may not
exceed 1 m/s
2. Place the measuring device in a defi ned position (prefe-
reably the zero position).
3. Select the "Adjustment" menu item under "SERVICE" in
the confi guration software. In the "Mechanical position"
window enter the current angle of the measuring device
and then select "Adjust". The measuring device is now
confi gured for the defi ned angle.
Programming
connector
Ancillary cable
KINAX WT711
Fig. 6
16
Interface
PK 610
OFF
ON
OFF: Power supply
by measuring output
(see Fig. 9)
ON: Power supply
provided by PC
8. Electrical connections
Screw terminals and one cable gland are provided for
making the electrical connections to the transmitter.
Note that, ...
... the data required to carry out the prescribed
measurement must correspond to those marked
on the nameplate (Fig. 7) of the KINAX WT 711
(Messeingang, Mess aus gang, Hilfsenergie)!
... the total loop resistance connected to the
output (receiver plus leads) does not ex-
ceed the maximum permissible value R
S e e " M e a s u r i n g o u t p u t " i n S e c t i o n
"5. Tech nical data"!
... twisted cores must be use for the measured
variable input and output leads and routed as
far away as possible from power cables!
In all other respects, observe all local regulations
when selecting the type of electrical cable and
installing them!
º,
In the case of "Intrinsically safe" explosion-
proof versions, the supplementary information
given on the EC-Type-Examination Certifi cation,
the EN 60 079-14 and also local regulations
applicable to electrical installations in explosion
hazard area must be taken into account!
!
0.5
camille bauer AG, CH-5610 Wohlen, Switzerland
Fig. 7. Example of a nameplate.
8.1 Connecting transmitter
The screw terminals are suitable for wire gauges up to
2
1,5 mm
and are accessible when the cover is removed.
5
6
Fig. 8. Housing (1) with the cover removed showing the screw
terminals (5) and cable glands (2).
Type: WT711-1100 0000 0
Ord.: 000/000000/000/000
Supply
Range:
0...50º
Voltage
Output:
2-wire, 4...20mA
12...33V DC
Rotation Sense:
!
ext.
linear
1
3
4
2
Publicité
Chapitres
Table des Matières
