HIKOKI CM 5MA Mode D'emploi page 8

English
Standard Accessories
In addition to the main unit (1 unit), the
package contains the accessories listed in the
below.
○
2-hole spanner ................................................1
○
Chase chisel....................................................1
○
Plastic case .....................................................1
○
Diamond cut-off wheels* .................................2
* (WT) specifications is excluded.
Standard accessories are subject to change without
notice.
Specifications
Model
1
Voltage*
Rated input power
No-load speed
Diameter of the
diamond cut-off wheels
Groove width options
Adjustable depth of cut
Weigh without mains
2
cable*
*1 Be sure to check the nameplate on product as it
is subject to change by areas.
*2 Weight: According to EPTA-Procedure 01/2003
Note: Due to HiKOKI's continuing program of
research and development, the specifications
herein are subject to change without prior notice.
Initial Operation
1 Mains connection
Before commissioning, check that the rated
mains voltage and mains frequency, as stated
on the type plate match your power supply.
Always install an RCD with a maximum trip
current of 30 mA upstream.
Pay attention to a possibly short feed line and
a large line cross-section of the mains cable.
2 Use / change diamond cut-off wheels, set
groove width
Switch off the machine. Disconnect the mains
plug!
Caution! Never press the locking button (7)
when the machine is running (nor when it is
slowing down)!
8
CM5MA
– ∼
220 240 V
1900 W
-1
5000 min
125 mm
9.0 / 15.5 / 22.0 / 28.5 /
35.0 mm
–
10 40 mm
4.7 kg
Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool, it
does not assure safe operation. (see Accessories)
Fig. 5
- Set max. cutting depth (Setting cutting depth).
- Press the spindle locking button (7), (with the
other hand) rotate the front diamond cut-off
wheels (18) slowly until the spindle locking button
engages perceptibly and
- with the pressed spindle locking button (7)
unscrew the clamping nut (17) with the supplied
2-hole spanner (anti-clockwise).
The clamping flange (19) must always be fitted onto
the spindle with the sheath facing out (as shown in
the Fig. 6 (A) – (F). Pay attention that the clamping
flange (19), in relation to the spindle, cannot be
turned.
Fit the diamond cut-off wheels and pay
attention to the correct direction of
rotation. The direction of rotation is specified by
arrows (16) on the diamond cut-off wheels and on
the guard (15).
Arrangement of the spacer rings (20) and the
diamond cut-off wheels (according to desired
groove width) as in the Fig. 6 (A) – (E).
Note: Using the machine with only one diamond
cut-off wheel:
If you remove the front diamond cut-off wheel and
leave only the rear wheel on the machine, the wall
chaser is then suited for cutting through materials
(e.g. tiles).
(Fig. 6. F.).
Note: (Fig. 6. G.) Use of the machine with diamond
cutting wheels (see Accessories):
To be able to attach the diamond cutting wheels,
you must remove the clamping flange (19) from the
spindle and remove from the guard (15). Now put
the diamond cutting wheels on the clamping flange
(19), insert from below into the guard and put onto
the spindle. Pay attention that the clamping flange
(19), in relation to the spindle, cannot be turned. Put
on spacer rings (20) as shown in image (G).
Lock the spindle by pressing the spindle locking
button (7) and tighten the clamping nut (17) with the
two-hole wrench (14) (clock-wise direction).
Carry out a test run: Set min. cutting depth
(Setting cutting depth). Position yourself and
bystanders away from the plane of the rotating
wheel and run the power tool at maximum no-load
speed for one minute. Damaged wheels will
normally break apart during this test time. Stop
immediately if significant vibrations occur or if other
defects are noted. If such a situation occurs, check
the machine to determine the cause.