HIKOKI CM 5MA Mode D'emploi page 6

English
o) Regularly clean the power tool's air vents.
The motor's fan will draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
p) Do not operate the power tool near
flammable materials. Sparks could ignite these
materials.
q) Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock.
2 Kickback and related warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel. Pinching or snagging
causes rapid stalling of the rotating wheel which in
turn causes the uncontrolled power tool to be forced
in the direction opposite of the wheel's rotation at
the point of the binding.
For example, if an abrasive wheel is snagged or
pinched by the workpiece, the edge of the wheel
that is entering into the pinch point can dig into the
surface of the material causing the wheel to climb
out or kick out. The wheel may either jump toward or
away from the operator, depending on direction of
the wheel's movement at the point of pinching.
Abrasive wheels may also break under these
conditions.
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and
can be avoided by taking proper precautions as
given below.
a) Maintain a firm grip on the power tool and
position your body and arm to allow you to
resist kickback forces. Always use auxiliary
handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator can control torque reactions or
kickback forces, if proper precautions are taken.
b) Never place your hand near the rotating
accessory. Accessory may kickback over your
hand.
c) Do not position your body in line with the
rotating wheel. Kickback will propel the tool in
direction opposite to the wheel's movement at the
point of snagging.
d) Use special care when working corners,
sharp edges etc. Avoid bouncing and snagging
the accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory and
cause loss of control or kickback.
e) Do not attach a saw chain, woodcarving
blade, segmented diamond wheel with a
peripheral gap greater than 10 mm or toothed
saw blade. Such blades create frequent kickback
and loss of control.
f) Do not "jam" the wheel or apply excessive
pressure. Do not attempt to make an excessive
depth of cut. Overstressing the wheel increases
the loading and susceptibility to twisting or binding
of the wheel in the cut and the possibility of kickback
or wheel breakage.
6
g) When wheel is binding or when interrupting
a cut for any reason, switch off the power tool
and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the wheel from the cut while the
wheel is in motion otherwise kickback may
occur. Investigate and take corrective action to
eliminate the cause of wheel binding.
h) Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully re-enter the cut. The wheel may bind,
walk up or kickback if the power tool is restarted in
the workpiece.
i) Support panels or any oversized workpiece
to minimize the risk of wheel pinching and
kickback. Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge of
the workpiece on both sides of the wheel.
j) Use extra caution when making a "pocket
cut" into existing walls or other blind areas. The
protruding wheel may cut gas or water pipes,
electrical wiring or objects that can cause kickback.
3 Additional Safety Instructions:
WARNING – Always wear protective
goggles.
Wear a suitable dust protection mask.
Use only diamond cut-off wheels.
Do not use bonded discs.
Always operate with two hands.
Ensure that the place where you wish to work is free
of power cables, gas lines or water pipes (e.g.
check using a metal detector).
The workpiece must lay flat and be secured against
slipping, e.g. using clamps. Large workpieces must
be sufficiently supported.
The diamond cut-off wheels must fit without play in
relation to the support flange. Do not use adapters
or reducers.
Diamond cut-off wheels must be stored and
handled with care in accordance with the
manufacturer's instructions.
Ensure that the diamond cut-off wheels are installed
in accordance with the manufacturer's instructions.
Use elastic cushioning layers if they have been
supplied with the grinding media and if required.
Ensure the sparks emitted during use do not pose
any risk, for example, to the user or other personnel
and are not able to ignite inflammable substances.
Areas at risk must be protected with flame-resistant
covers. Always keep a fire extinguisher on hand
when working in areas prone to fire risk.