Technical Data; Noise & Vibration; Dust Collection System; Care & Maintenance - Pattfield Ergo Tools PE-600 MHKS-2 Traduction De La Notice D'origine

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 12

Technical Data

Nominal voltage
Rated power
No-load speed (n
)
0
Blade dimensions
Max. cutting depth (Wood)
Weight
Protection Class
Laser class
Sound pressure level (L
)
pA
Sound power level (L
)
WA
Max. vibration emission (a
)
hw
The values given are valid for nominal voltages U of 230 V. For lower voltage and models for
specific countries, these values may vary.
Please observe the article number on the type plate of the tool. The trade names of the individual
tool may vary.
Noise & Vibration
The declared vibration total value and the de-
clared noise emission values have been meas-
ured in accordance with a standard test meth-
od (EN 62841) and may be used for comparing
one tool with another. The declared vibration
total value may also be used in a preliminary
assessment of exposure.
Warning! The vibration and noise
emission during actual use of the
power tool can differ from the declared to-
tal value depending on the ways in which
the tool is used, in particular, what kind of
work piece is machined.

Dust collection system

Use of dust collection can reduce dust-related
hazards.
To prevent personal injuries, make sure to
176
EN
230-240 V~ / 50 Hz
500 W
7000/min
ø 85 mm x ø 10 mm x 1.6 mm
25 mm
1.7 kg
/ II
2 (Max. rad. 1 mW, 650 nm)
90 dB(A) / Uncertainty K = 3 dB(A)
101 dB(A) / Uncertainty K = 3 dB(A)
4.17 m/s
/ Uncertainty K = 1.5 m/s
2
2
Warning! It is necessary to identify
safety measures to protect the op-
erator that are based on an estimation of
exposure in the actual conditions of use
(taking account of all parts of the operating
cycle such as the times when the tool is
switched off and when it is running idle in
addition to the trigger time).
Try to minimize the impact of vibration and
noise. Exemplary measures to reduce vibra-
tion exposure include wearing gloves while
using the tool, limiting working time, and us-
ing accessories in good condition.
connect a suitable vacuum cleaner to the dust
extraction
port 10
by means of the dust col-
lecting system adaptor.
Care & Maintenance
Caution! Make sure the tool is
switched off and unplugged.
- Always keep the tool clean, dry and free of
oil or grease.
- Store the machine and its accessory in a
dry place and out of the reach of children.
- Wear safety glasses to protect your eyes
whilst cleaning.
- For safe and proper working, always keep
the machine and ventilation slots clean.
- Regularly check to see if any dust or foreign
matter has entered the grills near the mo-
tor and around the on/off switch. Use a soft
brush to remove any accumulated dust.
- If the body of the tool needs cleaning, wipe
it with a soft damp cloth. A mild detergent
can be used but nothing like alcohol, petrol
or other cleaning agent.
- Never use caustic agents to clean plastic
parts.

Accessory

Caution! The saw blade shall com-
ply with EN 847-1
- Do not use cracked or deformed saw blades.
- Do not use blades that do not match the
given parameters.
- Take care to properly fix the blade. Check
that the blade turns in the right direction.
- Lubricate all moving parts at regular inter-
vals.
- Periodically clean the laser generator from
sawdust.
- Periodically check all fixings. These could
become loose with time due to vibration.
- In case of excessive sparking the carbon
brushes should be checked by a qualified
electrician. Important: The carbon brushes
shall only be removed or replaced by a qual-
ified electrician.
- Service and maintenance works not de-
scribed in this manual are only to be carried
out by the manufacturer, its service agent or
similarly qualified persons.
Caution! If the supply cord is dam-
aged, it must be replaced by the
manufacturer or its service agent or simi-
larly qualified person in order to avoid haz-
ard.
Warning! Replacement parts must
conform with the requirements spec-
ified by the manufacturer. Therefore use
original replacement parts only or spare
parts authorised by the manufacturer.
Diamond cut-off wheel: art-nr. 5527692
In case of service requests or spare parts,
please contact your local HORNBACH store or
write an email to: service@hornbach.com
EN
177

Publicité

Table des Matières
loading

Table des Matières