L.B. White L-40 Mode D'emploi page 7

Attention - Critical
Points to Remember!
■ Propane gas and natural gas have a distinctive
odor. Learn to recognize these odors. (Reference
"Fuel Gas Odor" and "Odor Fading" sections
above.
■ If you have not been properly trained in repair and
service of propane gas and natural gas fueled
heaters, then do not attempt to light the heater, per-
form service or repairs, or make any adjustments
to the heater on a propane (LP) gas or natural gas
fuel system.
■ Even if you are not properly trained in the service
and repair of radiant heaters, ALWAYS be con-
sciously aware of the odors of propane gas and
natural gas.
■ A periodic "sniff test" around the heater or at the
heater's joints; i.e. hose, connections, etc., is a
good safety practice under any conditions. If you
smell even a small amount of gas, CONTACT
YOUR FUEL GAS SUPPLIER IMMEDIATELY. DO
NOT WAIT!
1. Do not attempt to install, repair or service this
heater or the gas supply line unless you have
continuing expert training and knowledge of gas
heaters.
QUALIFICATIONS FOR SERVICING AND
INSTALLATION:
a. To be a qualified gas heater service person, you
must have been trained in gas-fired heater servic-
ing, repair and also have sufficient experience to
allow you to troubleshoot, replace defective parts,
and test heaters in order to get them into a continu-
ing safe and normal operation condition. You must
completely familiarize yourself with each model
heater by reading and complying with the safety
instructions, labels, owner's manual, etc. that is
provided with each heater.
b. To be a qualified gas installation person, you must
have sufficient training and experience to handle
all aspects of installing, repairing and altering gas
lines, including selecting and installing the proper
equipment, and selecting proper pipe size to be
used. This must be done in accordance with all
local, state and national codes as well as the
manufacturer's requirements.
L-40 / H-40 Spark Ignition Radiant Brooder
2. All installations or applications of L. B. White
Company, LLC's radiant heater shall meet the
requirements of local, state and national L.P. gas
and natural gas, electrical and safety codes. Your
gas supplier, local licensed electrician, local fire
department and government agencies can help
you determine these requirements. In the absence
of local codes, comply with the following:
-- ANSI/NFPA 58, latest edition, Standard for Storage
and Handling of Liquefied Petroleum Gas and/or
-- ANSI Z223.1/NFPA 54, National Fuel Gas Code
-- ANSI/NFPA 70, National Electrical Code.
--CAN1-B149.1/2 Installation Codes for Canada.
3. If at any time you notice something unusual about
the operation of your heater such as gas odor,
overheating, flames other than in the combustion
cone area, etc., evacuate the area immediately
and call your fire department and your gas service
agency. Get assurances from the fire department
that the area is free of gas before you attempt to
relight the heater.
4. The components on the heater that call for hand
operation should work with hand pressure only. If
more force is required, have a qualified gas heater
service agency replace the complete part. Do not
attempt to repair.
5. This heater is intended for the heating of livestock
in agricultural animal confinement buildings only.
The heater shall only be mounted inside the animal
confinement building. It shall not be used for
outside heating applications.
6. Do not locate fuel gas containers or fuel supply
hoses anywhere within the heating zone of the
heater.
7. Do not block the air intake, or burner emitter area.
Doing so may cause improper combustion or
damage to the heater components, leading to
property damage or animal loss.
8. Do not move, handle, or service the heater while in
operation or connected to fuel supply.
9. The hose assembly must be inspected on a regular
basis. This should be done at least once a year,
or when the building is cleaned out. If it is evident
there is excessive abrasion or wear, or if the hose
Owner's Manual • L-40 / H-40
7