Editing.the.tone.settings; Editing The Tone Parameters - Roland Lucina AX-09 Mode D'emploi

Editing the Tone Settings

Editing the Tone Parameters

You can edit tone parameters such as the volume and
reverb for a regular tone, and save your settings in a
FAVORITE memory location (p. 10).
* You.can't.edit.the.tone.parameters.of.a.special.tone .
1. Select.the.regular.tone.whose.tone.parameters.
you.want.to.edit.(p ..9) .
2. Hold.down.the.[SHIFT].button.and.press.the.TONE.
button.of.the.tone.you.selected.in.step.1.(i .e .,.the.
TONE.button.that's.lit) .
The parameter name (
oF F
then its value ( or
3. Continue.holding.down.the.[SHIFT].button,.and.
press.the.same.TONE.button.to.switch.parameters .
The parameters will switch from top to bottom of the
"Parameter" column in the following table.
* Don't.release.your.finger.from.the.[SHIFT].button.while.
making.this.setting .
Parameter Value
OFF, ON
PS
PtN
0–127
uoL
0–127
rEu
0–127
rEL
-64–63
-64–63
At
CUt
-64–63
rES
-64–63
16
P S
) will blink in the display, and
o n
) will appear.
Explanation
Portamento.Switch
Portamento is an effect that creates a
smooth change in pitch from one note
to the next.
Portamento.Time
This specifies the time over which
the pitch will change when using
portamento. Higher values will lengthen
the time over which the pitch will reach
the next note.
Volume
This specifies the volume of the tone.
Reverb
This effect adds the reverberation that
is characteristic of a performance in a
large hall. Higher values produce deeper
reverberation.
Release.Time.(*1)
This adjusts the time from note-off
(i.e., when you release the key) until
the sound disappears. Higher values
produce a longer release time.
Attack.Time.(*1)
This adjusts the sharpness (speed) at
which the sound begins. Higher values
produce a more gentle attack.
Cutoff.(*1)
Increasing the cutoff value will make
the sound harder (brighter); decreasing
it will make the sound more mellow
(darker). Use this parameter to make
adjustments if the sound is too muffled
or too bright.
Resonance.(*1)
Increasing the resonance value will
produce a distinctive tonal character
that is typical of a synthesizer. If you
want to emphasize the effect of
resonance, it's a good idea to slightly
lower the cutoff.
*1 The values you specify here are an adjustment relative to the value
assigned by each tone. If this value is set to 0, the parameter will be as
specified by the tone's own settings.
4. When.the.parameter.value.appears,.continue.
holding.down.the.[SHIFT].button.and.use.the.
[INC/+]./.[DEC/–].(OCTAVE.[+]./.[–]).buttons.to.edit.
the.value .
MEMO
• You can make the value change more quickly by
holding down the [INC/+] / [DEC/–] button. If you want
the value to change even faster, hold down the button
and press the other button as well.
• Even while editing the value, you can play the keyboard
to hear the result.
5. Release.the.[SHIFT].button .
* If.you.select.a.different.sound.or.turn.off.the.Lucina.
AX-09's.power.in.this.state,.the.changes.you.made.will.
be.lost ..If.you.want.to.keep.your.changes,.you.must.store.
them.in.a.FAVORITE.memory.location.as.follows .
6. Press.the.[WRITE].button .
The [WRITE] button will light.
7. Press.the.FAVORITE.[A].button.or.[B].button.to.
select.a.bank .
8. Press.one.of.the.TONE.[1]–[6].buttons.to.select.the.
memory.location.in.which.you'll.store.the.settings .
When the [WRITE] button goes out, the settings have been
stored.