Erreka VIVO-M203 Guide Rapide D'installation Et Programmation page 15

D1 D2 Parameter
C 0
Number of operators
1
Operator 1 turning direction
(operator 2 also changes)
2 Operator 2 turning direction
(operator 1 also changes)
3
Gate type
4
O p e n i n g s a f e t y
(photocell)
5
Closing safety device (photocell)
Closing photocell with C520 or
C 5 2 1 , a l s o p r e v e n t s g a t e
opening from starting
6 Electrolock / electromagnet
C630 and C640 are used to
manage an external relay at
24Vdc, connected to cable
c o n n e c t o r s P 1 1 - P 1 2 . T h e
e l e c t r o m a g n e t
externally supplied (through this
relay) and sized in line with the
electromagnets used.
7
Encoder / Limit switches
The cabling depends on the type
of operator selected (C301,
C 3 0 2 o r C 3 0 3 ) ; s e e t h e
corresponding wiring diagram)
8 Radio card
9
Safety strip
A
Slowdown
P 1
Total opening radio programming
2
Pedestrian opening radio programming
3
Programming gate travel
F 1 Key command by way of ST1
and ST2 pushbuttons.
With F101 the gate (total or
pedestrian) can be kept open by
keeping ST1 or ST2 pressed
down respectively. This allows
the time scheduler to be used in
combination with F2 and/or F4
K 00.
2
A u t o m a t i c o r s t e p - b y - s t e p
operation mode and standby
time (in seconds) in automatic
mode
3
Pedestrian opening (%)
4
Pedestrian closing mode
Complete programming chart (I)
D3 D4
0 1, 2
0 1, 2
0 1, 2
0 1 ... 3
0,1 0,1
d e v i c e
0...2 0,1
0...4 0...4
m u s t b e
0 0...5
0 1, 2
0 1, 2
0 0...3
o ç
o ç
o ç
0 0...4
0..5. 0...9
0...9 0...9
0...5 0...9
Default
Options or values
option
01 01: one operator,
02: two operators (only available with C301)
01 01: direction A, 02: direction B. Check direction by
pressing ST1 (open) and ST2 (close)
01 01: direction A, 02: direction B. Check direction by
pressing ST1 (open) and ST2 (close)
01 01: swing, 02: sliding, 03: up-and-over
00 00: not installed,
10: no testing, 11: with testing
00 00: not installed,
10: no testing, 11: with testing
20: no testing, 21: with testing
00 00: not installed
1X: electrolock
Programmable electrolock time: 3 seconds
with X=0 (by default), 3.5s with X=1, 4s with
X=2, 4.5s with X=3, 5s with X=4.
2X: electrolock
Programmable time (electrolock/motor
reverse): 4.5/1.5 seconds with X=0 (by default),
5/2s with X=1, 5.5/2.5s with X=2, 6/3s with
X=3, 6.5/5s with X=4.
30: electromagnet without impulse
40: drop electromagnet
00 00: not installed;
01: with single encoder;
02: with limit switches;
03: with dual encoder;
04: with encoder and limit switches (not available
with C301 selected);
05: VULCAN VUS and ATLAS (ATS) G6xxI (only
available with C301 or C303 selected)
02 01: RSD card (no decoder);
02: two channel decoder card
01 01: mechanical; 02: resistive 8k2
02 00: no slowdown;
01: slowdown in opening and closing;
02: slowdown in opening;
03: slowdown in closing
Programmes total opening channel and code
Programmes pedestrian opening channel and code
Programmes the operations in accordance with the
configuration CA
01 00: ST1 and ST2 without effect, the key commands
are given by radio (channel 1: total opening-
closing, channel 2: pedestrian opening-closing)
01: ST1 total opening-closing, ST2 pedestrian opening-
closing
02: ST1 total opening, ST2 total closing
03: dead-man mode (the display shows HP.);
04: dead-man mode in closing
00 00: step-by-step mode
01: automatic mode and standby time 1 second;
...
59: automatic mode and standby time 59 sec.;
1.0: 1 min. 0 sec.;
40 00: pedestrian opening is not carried out,
10: 10% of total opening, etc
00 00: semi-automatic mode
01: automatic mode and stand-by time 1 second;
...
59: automatic mode and stand-by time 59 sec.;
1.0: 1 min. 0 sec.; ...; maximum 4 minutes
without reverse impulse.
with reverse impulse.
...; maximum 4 minutes
15