Publicité
Les langues disponibles
Les langues disponibles
sired number and tighten the lobe knob again. You can
use the stop bar (20) of the rip fence (7) to improve the
work piece guidance by tightening the stop bar to the rip
fence using 2 groove screws and 2 star grip screws.
9. Using the saw
Follow the safety instructions!
Important: Be sure to mount all protection and
safety devices and to connect the power tool to
the exhaust system before commissioning the
electric power tool. Also make sure to lower the
protective cover to the work piece for any pro-
cess of the power tool.
Before turning on the electric power tool, all protec-
tion and safety devices have to be installed properly.
Ensure that the saw blade can move freely. Check
wood that has been processed already for foreign
objects (nails, screws and so on). Remove all foreign
objects and connect the power tool to a socket with a
ground. Before you turn on the main switch, ensure
that the saw blade is mounted properly and that the
movable parts are running smoothly. Warning: If you
have any doubts, let an expert assemble the power
tool. It is too dangerous to work on the basis of as-
sumptions.
ADJUSTING THE CUTTING HEIGHT Fig. 5
The saw blade has to be adjusted in such a way that
the top of the highest saw tooth is slightly higher than
the work piece.
The saw blade (4) can be adjusted to the intended
cutting height by rotating the height adjustment
handle (11. Rotating counter clockwise enlarges the
cutting height, rotating clockwise reduces the cutting
height.
ADJUSTING THE ANGLE OF THE SAW BLADE
Fig.6
Loosen the locking handle (14). You can adjust the
saw blade (4) to the intended angle on the scale (13)
by rotating the angle adjusting wheel (12). Tighten
the locking handle (14) again.
CALIBRATING THE ANGLE OF THE SAW BLADE.
Fig.7
Attention! Pull out the main plug
The scale (13) can be calibrated during the examina-
tion of the angular accuracy of the saw. Adjust the
saw blade at the very top; make sure to have a right
angle to the saw blade. Adjust the angle adjusting
wheel (11) in a way that the saw blade is parallel to
the angle.
Adjust the pointer to an angle of 0°.
SWITCH ON AND OFF
Green button = On
Red button = Off
22
GB
10. Operation
OVERLOAD PROTECTION
This electrical power tool is provided with an over-
load protection. In case that the overload protection
was initiated, proceed as follows:
Disconnect the power tool from the power supply.
Allow the power tool to cool down.
Check the power tool carefully for possible damages.
Have damages repaired before re-starting the power
tool.
Connect the power tool to the power supply.
Push the overload switch (17).
Turn on the power tool as described and put it into
operation.
WORKING WITH THE LONGITUDINAL STOP FIG. 8, 9
The stop bar (20) has two different guide surfaces.
Depending on the thickness of the work piece, the
stop bar for thick or thin material should be used.
Thick material (Fig. 8)
Thin material (Fig. 9)
Loosen both knurled screws and pull off the stop bar
(29) to it. Reattach the stop bar as required by the
locating heights and tighten both knurled screws.
WORKING ON SAWING MACHINES
Cutting broad work pieces, Fig. 10
Broadness of the processed work piece: more than
120 mm
Tool: circular saw blade for a longitudinal cut
Process: Adjust the longitudinal stop according to
the intended broadness of the work piece. Ensure
safe and best possible positioning of the hands.
In the case that narrow work pieces are detached
during the cutting process, you perform feed in the
mould area either by simply using your right hand or
by a push stick. If there is danger that the work piece
jams between the circular saw blade, splitting wedge
and limit stop, move the limit stop back to the centre
of the saw blade or use a short auxiliary stop.
Note: In all our figures, the upper suction hood is only
slightly indicated (or left out completely in individual
cases) which allows a better demonstration of the
processes or the equipment. The upper suction hood
is necessary to perform the shown processes!
Cutting narrow work pieces, Fig. 11
Broadness of the processed work piece: below
120 mm
Tool: circular saw blade for a longitudinal cut
Process: Adjust the longitudinal stop according to
the intended broadness of the work piece. Move the
work piece forward with both hands, use the push
stick in the saw blade area and move the work piece
until it passes the push stick. When working with
short work pieces, use the push stick for the com-
plete moving process.
Publicité
