Publicité
Les langues disponibles
Les langues disponibles
• Health hazard due to electrical power, with the use of
improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instruc-
tions" and the „Proper use" are observed along with
the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the machine
in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Hands may never enter the processing zone when the
machine is in operation. Release the handle button
and switch off the machine prior to any operations.
• Prior to any adjustment, maintenance or service work
disconnect the mains power plug!
6. Technical data
AC motor
performance
Idle speed
Hard-metal blade
Number of teeth
Thickness riving knife
table size
Cutting height max. 90°
Cutting height max. 45°
suction port
weight
Protection class
Noise values
The total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
230-240 V~ 50Hz
1200 Watt
4800 min
-1
ø 210 x ø 30 x 2,6 mm
24
2,0 mm
525 x 400 mm
48 mm
45 mm
ø 36 mm
14 kg
II
93,2 dB(A)
3 dB
106,2 dB(A)
3 dB
7. Before starting the equipment
• The equipment must be set up where it can stand
securely, i.e. it should be bolted to a workbench, a
universal base frame or similar.
• All covers and safety devices have to be properly fit-
ted before the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails or
screws, etc.
• Before you press the ON/OFF switch check that the
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power sup-
ply make sure the data on the rating plate are dentical
to the mains data.
• Connect the machine to a properly installed protec-
tive contact socket, with at least 16A circuit breaker.
8. Assembly
Assembly and modification work may only be per-
formed when the mains plug is pulled out.
For packing-related reasons, the electrical power tool
must be mounted by the operator.
Open the box and remove the packaging and Styrofoam
parts.
Remove the enclosed individual parts.
Remove the power tool from the box and place it on the
floor. Ensure to use a piece of cardboard as a base in
order to protect the floor.
Note: The electrical power tool is heavy; thus two people
should lift the device out of its packaging.
ASSEMBLY PROTECTIVE COVER Fig. 2
In order to mount the protective cover (2), place it above
the splitting wedge (5), so that the screw fits into the slit
of the splitting wedge. Then, push the protective cover
into the bottom of the opening. Screw the wing nut tight,
so that the protective cover sits on the table top (1), but
lifts itself, when the work piece is pushed towards the
saw blade. Make sure to move the protective cover back
to its idle position after you have finished cutting.
Note: The protective cover (2) has to be in working posi-
tion at all times in order to avoid contact with the saw
blade.
ASSEMBLY LONGITUDINAL STOP Fig. 3
Use the star grip screws (27) to mount the clamping
claws (26) to the stop tube (28) on both sides. Use the
clamping claws to insert the longitudinal stop (7) laterally
into the table top (1).
Use the star grip screws to tighten the longitudinal stop
on both sides.
ASSEMBLY RIP FENCE Fig. 4
Insert the rip fence (13) into the groove on the saw
bench (1). Loosen the lobe knob (24), adjust to the de-
GB
21
Publicité
