Amana NFW7200TW Caractéristiques Techniques page 8

Troubleshooting
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
Selection Function
Rotary cycle
Medium water level
selector set to
Wrinkle Control.
Press Rotary
Selector Knob.
Press "Extra Rinse" Low water level
Rotary cycle
Tub balance
selector set to
Hand Wash.
Press Rotary
Selector Knob.
Press Delay
Water temperature
switch pad.
Rotary cycle Water temperature
selector set to
Delicates. Press
Rotary Selector
Knob.
Board Output Test
While in Service Mode, pressing the
Spin Speed key will begin the Board
Output Test. This test turns on a specified
output after a key press. Pressing the
Spin Speed key again cancels the test. Only one output
can be "on" at any time. All outputs will be turned off after
five (5) minutes of inactivity. While in Service Mode follow
to check respective function.
• When the "Rotary Cycle Selector" is set to "Super Wash"
and the "Rotary Cycle Selector" button is pressed, the
Main relay will be toggled (either from "on" to "off" or from
"off" to "on").
• When the "Rotary Cycle Selector" is set to "Normal" and
the "Rotary Cycle Selector" button is pressed, the hot
water valve will be turned on. This output will remain on
until the "Rotary Cycle Selector" button is pressed again to
turn off the output. The control will not allow the machine
to fill past the High water level.
• When the "Rotary Cycle Selector" is set to "Wrinkle
Control" and the "Rotary Cycle Selector" button is
pressed, the cold water valve will be turned on.
WARNING
Display
• When the "Rotary Cycle Selector" is set to "Delicates"
"—0 " if below level.
"—1" if above level.
"_0 " if below level.
• When the "Rotary Cycle Selector" is set to "Hand
"_1" if above level.
" UC " Balanced
" UO " Unbalanced
• When the "Rotary Cycle Selector" is set to "Quick
Degrees F
Degrees C
• Pressing the "Delay" switch pad will turn on the motor
• Pressing the "Chime" switch pad will unlock the door
• Pressing the "Temperature" switch pad will lock the
8
This output will remain on until the "Rotary Cycle
Selector" button is pressed again to turn off the output.
The control will not allow the machine to fill past the
High water level.
and the "Rotary Cycle Selector" button is pressed, the
bleach valve will be turned on. This output will remain
on until the "Rotary Cycle Selector" button is pressed
again to turn off the output. The control will not allow
the machine to fill past the High water level.
Wash" and the "Rotary Cycle Selector" button is
pressed, the valve will be turned on. This
Softener
output will remain on until the "Rotary Cycle Selector"
button is pressed again to turn off the output. The
control will not allow the machine to fill past the High
water level.
Wash" and the "Rotary Cycle Selector" button is
pressed, the drain pump will be turned on. This output
will remain on until the "Rotary Cycle Selector" button
is pressed again to turn off the output.
and the "Delay" LED. This output and the LED will
remain on until the "Delay" switch pad is pressed again
to turn off the output. When activated, the machine will
tumble for 5 seconds in the CW direction, pause for 2
seconds, tumble in the CCW direction for 5 seconds,
pause for 2 seconds; repeating this pattern until
"Delay" button is pressed again to turn off the tumbling.
Note that all tumble speeds are assumed to be 45 rpm.
and turn on the all the LEDs above the "Chime" button.
This output will attempt to unlock one time, if safe to do
so.
door and all the Temperature LEDs will turn ON.
Pressing the Chime button will unlock the door and the
all the Chime LEDs will turn ON.