Amana NFW7200TW Caractéristiques Techniques page 7

Troubleshooting
To avoid risk of electrical shock, personal injury or death; disconnect power to washer before servicing, unless
testing requires power.
LED/Switch Test
While in Service Mode, press the Delay
key to start a LED/Switch check.
All the LEDs can be toggled or slewed by
pressing the key associated with the LED or set of
LEDs.
All keys (including the OFF button) must be pressed
within 5 minutes for this test to pass. "PA" will be
displayed for five (5) seconds once all keys have
been pressed and the test is completed. Following 20
seconds of inactivity at any point, this test will exit
without any display. The Power Off switch pad must
be pressed twice within 30 seconds to cancel this test.
Switch Action
Delay Start Press once
Chime Press 3 times
Extra Rinse Press once
Soil Level Press 4 times
Spin Speed Press 5 times
Temperature Press 5 times
Rinse&Spin Press once
Spin Only Press once
Selector Knob Rotate 1 full revolution clockwise
Selector Knob 1 position counterclockwise
Start Pause Press once
Selector Knob Press once
Power Off Press once
Board Input Test
While in Service Mode, pressing the
Spin Only key will begin the Board Input
Test. This test turns on a specified output
after a key press. Pressing the Spin Only
key again cancels the test.(Display shows in).
While in Service Mode follow chart to check respective
function.
• When the "Rotary Cycle Selector" is set to "Super Wash" and
the "Rotary Cycle Selector" is pressed, the door position will be
displayed: OP if open, CL if closed.
• When the "Rotary Cycle Selector" is set to "Normal" and the
"Rotary Cycle Selector" is pressed, the Lock position will be
displayed: UL if unlocked, LO if locked.
- When the "Rotary Cycle Selector" is set to "Quick Wash" and
the the "Rotary Cycle Selector" is pressed, the High water level
will be displayed: - 0 if below level, - 1 if above level. The High
water level is defined as the over flow water level.
WARNING
• When the "Rotary Cycle Selector" is set to "Wrinkle
Control" and the the "Rotary Cycle Selector" is
pressed, the Medium water level will be displayed:
-0 if below level, -1 if above level. The Medium water
level is defined as the minimum water level needed
such that the heater can be turned on.
• When the "Extra Rinse" is pressed, the Low water
level will be displayed:_0 if below level, _1if above
level. The Low water level is defined as the reset
water level.
• When the "Rotary Cycle Selector" is set to "Hand
Wash" and the the "Rotary Cycle Selector" is pressed,
the level of Tub unbalance will be displayed:UC if
balanced, UO if unbalanced. U0 will be displayed
during the time when the machine is correcting for the
unbalance; e.g. slowing down to redistribute the load
or to get to a lower spin speed. Once the situation has
been corrected (i.e. the load has begun tumbling or the
lower speed has resulted in an acceptable amount of
unbalance); UC will once again be displayed.
• When the "Delay" switch pad is pressed, the water
temperature will be displayed: degrees F.
- When the "Rotary Cycle Selector" is set to "Delicates"
and the "Rotary Cycle Selector" is pressed, the water
temperature will be displayed: degrees C (Celsius).
Selection
Rotary cycle
selector set to
Super Wash.
Press Rotary
Selector Knob.
Rotary cycle
selector set to
Normal. Press
Rotary Selector
Knob.
Rotary cycle
selector set to
Quick Wash.
Press Rotary
Selector Knob.
7
Function Display
Door position "OP" or "CL"
Lock state "UL" or "LO"
High water level " – 0" if below level.
" – 1" if above level.