Factory Setting (Reset); Calling Up The Event List; Showing System Information Changing Device Ids And Device Names; Switching Off The Recorder - Monacor AXR-104 Mode D'emploi

7.10 Factory setting (reset)

To reset the recorder to its factory settings:
1) Call up the main menu: Either press the button MENU at
the recorder/on the remote control or press the right mouse
button to call up the toolbar and then click the symbol
"Main Menu".
2) In the bar located at the top of the menu, click "Advanced".
Parameter Record Search
Maintain
Default User
Events
Auto Reboot
Reboot
Fig. 7-27 Menu "Advanced"
3) Click the field "Load Default".
Load Default
Display
Record
Network
Alarm
All Clear
Fig. 7-28 Window "Load Default"
4) A reset to the factory settings can be performed for all or
specific setting types. The setting types listed correspond
to the menus or submenus with the same name. To select
setting types, click the respective fields with the mouse.
Menu item
(Display etc.)
All
Clear
Save
Cancel

7.11 Calling up the event list

The recorder saves all events such as loss of camera signal,
switch-on and switch-off of the recorder, manual recording,
replay of a recording, changes to the menu settings etc.
Call up the menu "System" and then click the submenu "Log".
Parameter Record Search
General
Start Date 02/15/2017
Users
End Date 02/16/2017
Info Log Type All
Channel Type
Log
System
CH1 Alarm
CH2 Alarm
CH3 Alarm
CH4 Alarm
Storage
CH4 Alarm
Config
Fig. 7-29 Event list after a search request
Menu item Function
Start Date First day
End Date End day
Start Time Beginning
End Time End
Selection of an event group:
Log Type All, System, Config, Alarm, Users, Record, Storage
The group is shown in the column "Type".
54
i
Device System Advanced
admin
Enable
Every Week Sun. 00:00
Update Load Default IPC Upgrade
Load Settings Save Settings
IPC Load Default Reboot IPC
Default
Device
System
Advanced
Save Cancel
Function
To select a specific setting type
To select all setting types
To deselect the setting types selected
To reset the selected setting types to their
factory settings
To close the window
i
Device System Advanced
Start Time 00:00:00
3 0
End Time 23:59:59
3 0
Search
CON. RECORD
TIME
02/15/2017 11:17:54 System Startup
02/15/2017 11:17:54 VIDEO LOSS
02/15/2017 11:17:54 VIDEO LOSS
02/15/2017 11:17:54 VIDEO LOSS
02/15/2017 11:17:54 VIDEO LOSS
02/15/2017 11:23:07 No. 1 Format HDD
02/15/2017 11:30:41 Handy End
02/15/2017 12:02:36 ecording Schedule Settin
<< 1/4 1
Backup
of the search request
Menu item
Search
Backup
Cancel
To make sure that any tampering with the recorder is shown in
the event list, the list will not be deleted when the hard disk is
formatted or when the recorder is reset to its factory settings.
7.12 Showing system information
Shutdown
Changing device IDs and device names
Call up the menu "Device" and click the submenu "Info". The
section "Info" will be selected:
Parameter
General
Users
Info
Save Cancel
Info
Channel Info
Record Info
Log
Fig. 7-30 System information
In the line "Device ID", you can enter a specific identification
number, e. g. when multiple recorders are to be accessed via
a network. The recorders can only be addressed separately
when they have different ID numbers.
In the line "Device Name", a different name can be entered
so that it will be easier to distinguish multiple recorders from
each other by their name.
Two additional sections provide further information:
"Channel Info": Information with regard to the camera
"Record Info":
If required, refer to the menu overview in chapter 6.5.

7.13 Switching off the recorder

Prior to using the POWER switch, shut down the recorder
properly. Otherwise, settings or current recordings may be lost.
1) Call up the toolbar: Either press the right mouse button or
Shutdown
move the mouse pointer to the centre of the lower edge
of the screen.
Playback
No
Fig. 7-31 Toolbar
No
No
No
2) Click the symbol
Yes
3) Click the symbol
>>
menu. The following message will appear:
Cancel
Recording was stopped successfully, you can turn
Abb. 7-32 Message to inform the user that the recorder can be
4) Switch off the recorder with the rocker switch at the rear.
Note: The power supply unit connected has a low power consumption
even when the recorder is switched off. If applicable, switch the power
supply unit off by means of a power strip with on/off switch.
Function
To start a search request
To save the list to a USB flash drive, for example
To close the window
i
Record Search Device System
Device ID 000000
Device Name 1080P-HY04N
Device Type HY-DVR
Hardware Version DM-284
Software Version V7.1.0-20160719
IE Client Version V2.0.0.867
IP Address 192.168.1.159
MAC Address 00-23-63-63-FR-A7
HDD Volume 931G
Video Format PAL
P2P ID RSV160700970782
channels
Information with regard to the recording
settings
"Main Menu".
"Shutdown" in the upper right of the
Warning
off the power safely now !
switched off
Advanced Shutdown
QR code
P2P ID
Save Cancel