Setting Dwell Time And Display For Image Sequence; Magnifying An Image Section - Monacor AXR-104 Mode D'emploi

According to the factory settings, each camera image is
designated by the name "CH-" and the number of the chan-
nel. If required, the names can be changed, e. g. to "Stock-
room", "Entrance", "Checkout area" etc. (see chapter 6.9).
A prefix, indicating the camera type, is added to the name:
Prefix Camera type
None Analog camera with CVBS signal
A- AHD camera (Analog High Definition)
C- CVI camera
T- TVI camera
The live surveillance will not have any influence on the current
recording (indicated by the symbol
is possible to enlarge individual camera images or a selection
of images.
Display Action
With the left mouse button:
Double-click the image desired.
Individual image
At the recorder or with the remote control:
in
Press the corresponding numeric key 1 ... 9 or the
full-screen mode
button CH– / CH+ (AXR-104, AXR-108);
channels 10 ... 16: Button 1 and button 0 ... 6
With the left mouse button:
Double-click the full-screen display.
Return to the
At the recorder or with the remote control:
display of
all camera images
Press the button ALL (repeatedly) or the button
(AXR-116).
With the mouse: Press the right mouse button to
show the toolbar. Then select the view:
Symbol
Different numbers
of camera images
Additional
Click the layout symbol repeatedly to switch to
additional camera channels.
At the recorder or on the remote control:
Press the button ALL (repeatedly) or the button
(AXR-116).
Use the mouse to click the symbol
Sequence of all
in the toolbar. For setting the dwell time, refer to
full-screen images
the figures in the following chapter. To terminate
the sequence, click the symbol
7.3.1 Setting dwell time and
display for image sequence
The dwell time is factory-set to 5 seconds. To change the
dwell time:
1) Call up the main menu. Either press the button MENU at
the recorder/on the remote control
or with the mouse:
Show the toolbar: Press the right mouse button or move
the mouse pointer to the centre of the lower edge of the
screen.
Fig. 7-6 Toolbar
and click the symbol
(Composite Video Interface)
(Transport Video Interface)
R
in the camera image). It
Images AXR-104 AXR-108 AXR-116
4
 
9 —

12 —

16 — —
25 — —
 
layouts
"Start SEQ"
again.
"Main Menu".
Parameter Record Search
Display
Analog Channels
IP Channels
Live
Output
Image Control
Privacy Zone
Record
Capture
Network
Alarm
Fig. 7-7 Main menu
2) The submenu "Display" in the menu "Parameter" will be
selected. In the submenu, click "Output" (without any
symbol) to the left.
Parameter Record Search
Display
Video Output
Analog Channels
Seq Mode
IP Channels
SEQ Dwell Time
Live
VGA/HDMI Resolution
Transparency
Output
Support Overscan
Image Control
Privacy Zone
Record
Capture
Network
Alarm
Fig. 7-8 Menu "Parameter", submenu "Display", section "Output"
3) In the line "Seq Mode", it is possible to switch from
single-image mode (Layout1) to multi-image mode: Click

the symbol


4) To change the dwell time, click the field with the number

"5" in the line "SEQ Dwell Time" and then enter the time

in seconds.

5) To save the setting, click "Save". The message "Save
Parameters Successful !" will appear. Click "OK".
6) Click "Cancel" to exit the menu window.

7.3.2 Magnifying an image section

1) Using the left mouse button, click the live image in which
you want to magnify an image section. (In the single- image
mode, simply press the left mouse button.)
The quick-selection bar will appear:
Fig. 7-9 Quick-selection bar for each camera image
2) Click the magnifier symbol
mode, the display will change to the full-screen mode.
A magnifier symbol will appear; use this symbol to draw
a rectangle that will define the section to be magnified.
3) To go back to the normal full-screen mode, press the left
mouse button. The zoom function will remain active: It is
possible to magnify another image section.
4) To disable the zoom function, press the right mouse button.
Then, with a double click of the left mouse button, it will
be possible to return to the multi-image mode.
i
Device System
Channel Channel Name
CH1 CH1
CH2 CH2
CH3 CH3
CH4 CH4
Analog Channels CH1 CH2
i
Device System
LIVE-OUT
Layout1
5
1280x1024

to the right of the line.
. When in the multi-image
Advanced Shutdown
State
Enable
Enable
Enable
Enable
CH3 CH4
Save Cancel
Advance Shutdown
0
Default Save Cancel
49