Additional Safety Warnings - Scheppach CMT200-20ProS Traduction Des Instructions D'origine

4. Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if detachable,
from the power tool before making any ad-
justments, changing accessories, or storing
power tools. Such preventive safety measures
reduce the risk of starting the power tool acciden-
tally.
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to oper-
ate the power tool. Power tools are dangerous in
the hands of untrained users.
e) Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpect-
ed situations.
5) Service
a) Have your power tool serviced by a qualified
repair person using only identical replace-
ment parts. This will ensure that the safety of the
power tool is maintained.

6. Additional Safety Warnings

Device-specific safety instructions for Multi-tool
• This power tool is designed for sawing, cutting,
grinding and sanding. Read all safety warnings, in-
structions, illustrations and technical data supplied
with this power tool. Failure to follow the instruc-
tions below can lead to electric shocks, fire and/or
serious injuries.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Use clamps or another practical method to secure
and support the workpiece on a stable surface. If
the workpiece is held only by hand or against the
body, it will be in an unstable position that may re-
sult in a loss of control.
• Avoid cutting nails. Inspect the workpiece for any
nails and remove them before work.
• Before switching on the machine, make sure that
the application tool does not touch the workpiece.
• Keep hands away from moving parts
• Do not leave the machine running unattended. Only
use the machine with a hand posture.
• Always switch the machine off and wait until the
saw blade has come to a complete standstill, be-
fore removing the saw blade from the workpiece.
• Avoid touching the application tool or workpiece
immediately after machining because the parts are
still very hot and can cause burns on skin.
• Do not let the machine idle unnecessarily.
• Always use the correct dust protection or breathing
mask for the respective material and application.
• Some materials may contain toxic chemicals. Take
precautions to prevent inhalation of working dust
and contact with skin. Follow the safety data of the
material manufacturer.
• Do not wet the workpiece surface with water be-
cause this machine is not waterproof.
• Ensure adequate ventilation of the work area dur-
ing grinding operations.
• The use of this machine to sand certain products,
paints and wood may expose the user to dust
containing hazardous substances. Use suitable
breathing protection.
• Do not use accessories that are not specifically
designed and recommended by the tool manufac-
turer. The mere fact that an accessory can be at-
tached to your power tool does not guarantee safe
operation.
• Wear protective equipment. Depending on the
work, use a face shield or safety or safety goggles.
If necessary, wear ear protectors, gloves and a
work apron that is able to repel small grinding par-
ticles or workpiece splinters. The eye protection
must be able to repel the flying dust generated dur-
ing various operations. The dust mask or breathing
mask must be capable of filtering out particles gen-
erated by the work. Long-term exposure to noise
can lead to hearing damage.
• Keep bystanders at a safe distance from the work
area. Everyone entering the work area must wear
protective equipment. Fragments of the workpiece
or a damaged accessory may be thrown out and
cause injury beyond the immediate working area.
• Do not let the power tool run while you are carrying
it by your side. Otherwise, the accessory could ac-
cidentally catch your clothing in contact with it and
draw your body towards it.
GB | 19