Publicité
Les langues disponibles
Les langues disponibles
Put the battery in a plastic bag and follow the
instructions for battery disposal.
IF SKIN OR EYES COME INTO CONTACT WITH
THE ELECTROLYTE
Thoroughly rinse the area concerned with running
water.
Consult a doctor immediately.
IF THE ELECTROLYTE IS SWALLOWED
Rinse the mouth and spit out the water.
Consult a doctor immediately.
MAINTENANCE AND VEHICLE
CARE
• Do not disassemble or try to repair the vehicle on
your own. Contact an authorised Peg Perego
customer support centre.
• The toy should not be left anywhere with a
temperature below 0°C. If it were to be used
without being warmed up to a temperature above
0°C, irreversible damage could be caused to the
motors and batteries.
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the
plug connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used.
• Always disconnect the battery charger from the
toy before carrying out cleaning, maintenance, or
any type of intervention.
• For repairs use only original PEG PEREGO spare
parts.
• PEG PEREGO do not accept any responsibility for
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc.
Using the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or
motors, unless authorized by PEG PEREGO.
RULES FOR SAFE DRIVING
For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
WARNING!
• Make sure that all the nuts and bolts of the wheels
are tightened properly.
• If the vehicle is overloaded, the switch will
automatically disconnect the power and will trigger
an INTERMITTENT BEEP for 15 seconds, after
which the power supply is restored and the vehicle
will start operating again.
• Overheating can be caused by prolonged use under
the following conditions:
1 - Excessive load
2 - Excessively steep slopes
3 - Use on soils with tall grass
4 - Use on excessively soft soils (mud or sand)
5 - Use on uneven surfaces (e.g., rough ground,
stones, roots)
6 - The vehicle is stuck with a locked steering
wheel
7 - A combination of all these conditions
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
IF THE VEHICLE IS NOT WORKING:
• When the vehicle is overloaded (e.g., against a
fixed object, on deep soft mud or sand, or rough,
uneven ground), the overload switch will
automatically disconnect the power. The vehicle
restarts after a pause of at least 15 seconds.
However, to resume normal vehicle operation, you
have to solve the situation that caused the
overload first.
• If the vehicle stands still for more than 20 minutes,
repeat the starting procedure using the ignition key
until you hear the beep.
• The radio control will deactivate if it remains in
search mode (blinking blue LED) for more than 2
minutes. To reactivate it, turn it off and then on
again. The blue LED will start blinking again.
• If you hear a CONTINUOUS BEEP, it's time to
charge the battery.
• If you don't hear the initial beep, it means that the
battery is flat and needs to be charged.
• If the problem persists after charging the battery,
have the battery and battery charger checked at a
service centre.
• Make sure that all the plugs are connected
correctly.
• Check the electric switches and, if necessary,
replace them.
• Make sure that the battery is connected to the
electric circuit.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.
CUSTOMER SERVICE
PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://global.pegperego.com/toys-
site/support/
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
THE VEHICLE MUST BE ASSEMBLED BY ADULTS.
BEWARE WHEN EXTRACTING THE VEHICLE
FROM THE PACKAGING.
ALL THE NECESSARY SCREWS AND SMALL
COMPONENTS ARE STORED IN A BAG INSIDE
THE PACKAGING.
THE BATTERY MAY ALREADY BE INSTALLED.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while
assembling the toy, given the risks caused by small
parts (ingestion hazard) and the plastic bags that
contain them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Place the vehicle upside down. Attach the central
part of the rear bumper, as shown in the figure.
2 • Rotate the bumper upwards and bring it to the
correct position (1). Press the points indicated by
the arrows (2) as shown in the detail.
3 • Fasten the rear bumper using the 4 screws
supplied.
4 • Place the bonnet. Press the point indicated by
the arrow to attach it.
5 • Apply the corresponding sticker to the
dashboard (see sticker sheet).
6 • Connect the electric wire of the bonnet to the
electric wire that comes out from the bodywork,
as shown in the figure.
7 • Place the bonnet onto the product.
8 • Fasten the bonnet using the 4 screws supplied,
referring to the sheet in the screws bag.
9 • Insert the door handle in their housings on the
bodywork. Warning: the handles are
asymmetrical. To identify them, follow the
diagram (DX: right; SX: left).
10 • Fasten the handle as shown in the figure.
11 • Assemble the rearview mirror by joining the two
pieces. 30 • Fasten them with the screw
provided.
• Repeat the operation for the other rearview
mirror.
12 • Insert the rearview mirror as shown in the
figure, pressing down the indicated point (A);
13 • Fasten the rearview mirror by tightening the
screw provided.
• Place the product on its other side. Install the
remaining handle and rearview mirror.
• Reposition the product on its four wheels.
14 • Press the gear lever cover making the two parts
coincide.
15 • Press the piece indicated in the figure down on
the rear of the product.
16 • Press down the Fiat logo.
17 • Install the rear bumper as shown in the figure by
pressing the anchoring points.
18 • Place the two mirror cards inside the two rear
taillights.
19 • Install the rear taillights by inserting the upper
part (1); rotate the taillight (2) and press down
the lower part until attached.
20 • Press down the other Fiat logo at the front of
the vehicle.
21 • Apply sticker number 18.
22 • Press the inserts on each side of the Fiat logo.
23 • Insert the part of the front bumper indicated by
the arrow (1) into the hole on the bodywork.
Rotate and press the opposite side to engage it
(2). Note: the front bumper is made up of two
elements: DX (right) and SX (left) - see figure.
24 • Press down the front grid.
25 • Place two mirror cards inside the two front
taillights. Follow the diagram to insert the right
card inside each taillight.
26 • Install the front taillights by inserting the upper
part (1); rotate the taillight (2) and press down
the lower part until attached.
27 • Repeat the operation for the two smaller lights,
placing the mirror cards inside each one.
28 • Apply the light marked with DX to the right-
hand side of the vehicle and the light marked
with SX to the left-hand side. Note: the right-
and left-hand side are calculated sitting down
inside the cabin.
29 • Press the four caps onto the wheels, taking care
that the tabs coincide with the holes on the
rims.
30 • Install the spoiler on the sunroof inserting it in
the two slots.
31 • Tighten it from the back using the 3 screws
provided.
32 • Insert the unit you have just assembled into the
corresponding slots on the bodywork.
33 • Tighten it using the 2 screws provided.
34 • Press the button as shown in the figure and lift
the bonnet up.
35 • Insert the three pieces of the toy engine.
• The toy engine is like a puzzle that your child can
have fun putting together.
36 • Place the windscreen inserting the three tabs
into the front part of the bonnet.
37 • Fasten the windscreen using the two screws
supplied (one per side).
38 • Join the two parts of the steering wheel (steering
wheel and ring nut under the steering wheel)
together.
39 • Assemble the horn:
1- insert the spring;
2- remove the plastic tab from the sound
module. The sound module is provided with 3
LR44 batteries and is ready for use.
3- insert the sound module with the perforated
side facing downwards.
40 • Align the notches of the horn cover with the
ring nut and press them down on the steering
wheel.
41 • Install the steering wheel taking care that the
holes of the steering wheel coincide with those
of the stem.
42 • Insert the nut into the hexagonal hole of the
steering wheel and the screw into the circular
one. Tighten well.
43 • Connect the battery plug to the electrical system
plug.
44 • Place the seat inserting the rear part of the
backrest into the hole on the bodywork, as
shown in the figure (1). Rotate the seat into
position (2)
45 • Fasten the seat by rotating the lock with the help
of a tool or using a coin.
A: open saddle
B: closed saddle.
• Apply the remaining stickers according to their
Publicité
