Winterizing Your Unit; Self Help - Thermador DWHD640JFM Guide D'utilisation Et D'entretien

Masquer les pouces Voir aussi pour DWHD640JFM:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Waste water pump
Large food remnants in the rinsing water not retained by the filters may block the
waste water pump. The rinsing water does not get pumped out and covers the filter.
In this case:
• Disconnect the appliance from the power supply.
• Remove the filters.
• Scoop out water, use a sponge if required.
• Using a spoon, pry off pump cover (as illustrated) until it clicks, then grip the
cover by the lug and first pull it upward until it resists and then pull it out forward.
• Check inner compartment and remove any foreign objects.
• Place cover in the original position, press down and engage.
• Reinstall filters.
Clean the exterior door panel
Colored doors: use only a soft cloth dampened with soapy water.
Stainless steel doors: use a soft cloth with a non-abrasive cleaner (preferably a liquid
spray) made for cleaning stainless steel. For the best results, apply the stainless steel
cleaner to the cloth and then wipe the surface.
Clean the door gasket
Regularly clean the door gasket with a damp cloth to remove food particles and other debris. Also clean the door seal,
located inside the dishwasher at the bottom of the door.

Winterizing your unit

If your dishwasher will be unused for an extended period of time in a location that experiences freezing temperatures
(holiday home or through a vacation period), have your dishwasher winterized by an authorized professional service.
Turn your household water supply to the dishwasher off when on extended vacation or when dishwasher will not be
used for more than 1 month.

Self Help

Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher itself. The follow-
ing information may help you with a dishwasher problem without involving an authorized repair professional.
Problem
1. Door may not be properly latched
2. Unit may not be turned on
3. Unit not reset or previous cycle not completed
4. Delay start engaged
Dishwasher does
5. Interruption of electrical power supply to dishwasher
not start
or blown fuse
6. The door may have been closed without first select-
ing a cycle
7. Water supply may not be turned on
Dishwasher beeping
1. Default factory settings alert the customer that the
(end of cycle signal)
cycle is complete by beeping. This feature can be deac-
tivated if so desired
Display does not
1. A fuse may have been blown or circuit breaker
illuminate
tripped
2. Door not closed or latched
Note: For models with controls on top of the door, the
display only illuminates when the door is opened and
controls are visible.
Dishwasher seems
1. Incoming water is not warm enough
to run a long time
2. Cycle time can vary due to soil and water conditions
3. Rinse aid dispenser is empty
4. Dishwasher connected to cold water supply
Note: Refer to "Wash Cycle Information" (page 12-14)
section in this manual for typical cycle lengths
Cause
1. Shut the door completely until you hear it click
2. Press the main power switch to turn unit on
3. To reset, refer to "Cancel a Cycle" (page 15) in this manual
4. To reset, refer to "Delay Start" (page 15) section in this manual
5. Check circuit breaker
6. Select a cycle and close the door
7. Check and turn on water supply
1. To adjust the volume or deactivate, refer to the "Cycle Completion
Signal" (page 15) section in this manual
1. Check the fuse or circuit breaker box and replace the fuse or reset
the breaker if necessary
2. Ensure door is properly latched and completely closed
1. Before starting a cycle, run hot water faucet at the sink closest to the
dishwasher
2. Sensors in the dishwasher automatically increase the cycle time to
ensure a good wash when heavy soil is detected
3. Add rinse aid
4. Verify dishwasher is connected to hot water supply plumbing
2
Click
Action
1
3
19

Publicité

Chapitres

Table des Matières
loading

Table des Matières