English
Mounting
Application
Deluxe handsfree bus telephone
intercom with colour monitor for
Siedle In-Home bus
Functions:
•
Calling, hands-free/simplex
communication, video, door release
and storey call
•
Speech/control button
•
Colour monitor 8.8 cm (3.5")
•
Integrated video memory for
28 pictures, memory upgrade
possible using an SD card
•
Door release and light button
•
Buttons for switching and control
functions
•
Internal speech communication
•
Display of switching statuses
•
Muting button for call tone
•
11 ring tones
•
Call volume adjustable in 5 steps
•
Speech volume adjustable 5 steps
•
Monitor button for current picture
•
5-way button for video memory
and zoom function
•
Video memory function (only with
additional installation)
Intercom functions:
•
Call forwarding
•
Internal group call
•
Internal call with callback function
•
Collective announcement
•
Automatic call pick-up with
internal call
•
Doormatic
The intercom functions can only be
programmed using the bus program-
ming software BPS 650-...
Electrical voltage
Mounting, installation and ser-
vicing work on electrical devices
may only be performed by a
suitably qualified electrician.
Electrostatic charging
As a result of electrostatic
charging, direct contact with
the circuit board can result in
destruction of the device. Direct
contact with the circuit board
must therefore be avoided.
Scope of delivery
•
BFCV 850-... (Base plate and
housing with circuit board)
•
Dummy card for SD card slot
•
Operating instructions for the
end user
•
This product information
Mounting
Strip back cable to appr. 80 mm.
1
Recommended mounting height
appr. 1.50 m to centre device.
2
Open the device from the back;
by releasing the base plate with the
locking lever.
3
When mounting directly on the
wall, fasten the base plate using
4 screws, paying attention that
the plate is the right way up (top
marking). When mounting on a
switch box, use the screw openings
in the centre of the device, paying
attention that the plate is the right
way up (top marking).
4
Install in accordance with the
wiring diagram. The cores of the
installation cable must be stored
inside the free installation space in
the base plate.
5
Hook the housing into the base
plate from above and close by exer-
ting a slight pressure. Depending on
the installation environment, it may
be necessary to change the micro-
phone sensitivity of the BFCV 850-...
in order to permit clear speech
transmission. If a speech connection
exists, press the door release button
and light button simultaneously.
Using the speech button +/- the
microphone sensitivity can be set. If
no input is made within
10 seconds, the microphone setting
switches off again. Save the set
microphone sensitivity by pressing
the muting button for 3 seconds.
Dismantling
6
To remove the housing,
press the lock upwards using a flat
blade screwdriver. The circuit board
remains in the housing super-
structure.
Lettering
7
The lettering panel can be
inscribed to indicate the button
functions. The see-through panel
can be lifted at the side.
Terminal assignment
TaM/TbM = Input In-Home bus
TaM/TbM = Throughput In-Home
bus
ERT/ETb
= Storey call button
+M/-M
= Additional supply
20–30 V DC for video
memory function and
door parallel call
S1/S1
= Potential-free contact
for additional bell
Commissioning
Installation, commissioning and
programming are described in the
system manual (enclosed with line
rectifiers BNG/BVNG 650-... ).
Accessories for BFCV 850-...
ZTCV 850-... table-top accessory for
conversion from a wall-mounted to
a table-top device.
Specifications:
• The device is supplied via the
In-Home bus if the video memory is
not used
• Additional supply
20–30 V DC for the video memory
function / door parallel calls / inter-
com function current consumption
max. 350 mA
• Ring tone volume: max. 83 dB (A)
• Colour monitor 8.8 cm (3.5")
• Potential-free contact max.
15 V AC, 30 V DC, 1 A e.g. for
connection of an additional bell,
switching time 0.4 secs.–19 mins.
Video memory:
• 28 images in device memory
• SD card from 32 MB to 2 GB
5