Ivoclar Vivadent Bluephase C8 Mode D'emploi page 9

HIGH POWER Program
Consistently high light intensity for
the polymerization of restorative and
cementation materials for direct and
indirect restorations.
800 mW/cm
2
0 t [s]
LOW POWER Program
Reduced light intensity with reduced
heat development for the polymeriza-
tion of adhesives, liners, and restora-
tive materials in areas near the pulp
when restoring Class V cavities.
650 mW/cm
2
0 t [s]
SOFT START Program
Step-by-step increase of the light
intensity with reduced shrinkage
stress and reduced heat development
for the polymerization of restorative
materials.
800 mW/cm
2
650 mW/cm
2
0 5 t [s]
1) Applies to a maximum layer thickness of 2 mm and provided that the Instructions for Use of the respective material do not state any other recommendation (might be the case, e.g. with dentin shades)
2) Applies to a maximum layer thickness of 4 mm and provided that the Instructions for Use of the respective material do not state any other recommendation (might be the case, e.g. with dentin shades)
3) Applies to a maximum layer thickness of 3 mm 4) Applies to light-curing (use of the base past only)
Light intensity
Exposure time for composites
Exposure time for Tetric EvoCeram / IPS Empress Direct
Filling materials
Composite
• 2 mm
1)
IPS Empress Direct / IPS Empress Direct Flow /
Tetric EvoCeram / Tetric EvoFlow / Tetric /
Tetric Basic White / Tetric N-Ceram / Tetric N-Flow
Heliomolar / Heliomolar HB / Heliomolar Flow / Others
• 4 mm
2)
Tetric EvoCeram Bulk Fill
Tetric Basic White
Compomer
3)
Compoglass F / Compoglass Flow
Indirect restorations / Luting materials
Variolink II Base / Variolink Veneer / Variolink N Base
4)
/ Variolink N Clear Veneer / Variolink Ultra
4)
Dual Cement / Variolink II
5) 5)
Miscellaneous
Helioseal / Helioseal F / Helioseal Clear
Monopaque
MultiCore Flow / Multicore HB
Heliosit Orthodontic
Telio Add-On Flow
Telio Stains
IPS Empress Direct Color
IPS Empress Direct Opaque
Adhesive
AdheSE / AdheSE One F
ExciTE / ExciTE DSC
Tetric N-Bond / Tetric N-Bond Self-Etch
Heliobond (Syntac)
Temporary materials
Telio CS Inlay/Onlay
Systemp.inlay/onlay
Fermit / Fermit N
Telio CS Link / Systemp.link
Miscellaneous
Heliosit Orthodontic
Vivaglass Liner
Filling materials
Composite
• 2 mm
1)
IPS Empress Direct / IPS Empress Direct Flow /
Tetric EvoCeram / Tetric EvoFlow / Tetric /
Tetric Basic White / Tetric N-Ceram / Tetric N-Flow
Heliomolar / Heliomolar HB / Heliomolar Flow / Others
• 4 mm
2)
Tetric EvoCeram Bulk Fill
Tetric Basic White
Compomer
3)
Compoglass F / Compoglass Flow
5) Applies to dual-curing
Curing program
Bluephase C8
®
800 mW/cm ± 10%
2
20 s
15 s
Curing time
15 s
20 s
15 s
20 s
40 s
per mm ceramic:
/ 10 s per segment
5)
20 s
30 s
40 s
20 s
20 s
15 s
15 s
30 s
Curing time
10 s
10 s
10 s
10 s
20 s per segment
20 s
20 s
Curing time
20 s
25 s
20 s
25 s
40 s
13