Table des Matières
Publicité
Connection of High-Pressure Hose to the
Handle of the Gun and the Pump (Fig. 7)
Put the water pipe on the spray gun. Hold the end of the gun
and screw the pipe on it so that the connection is firm and
sure. Caution! Do not tighten the screw too much, both supply
connections may be damaged.
The supply connection of the high-pressure hose with the
supply connection on the bottom side of the spray gun handle
connect firmly and safely. Caution! Do not tighten the screw
too much, both supply connections may be damaged.
Safety Stop for High-Pressure Water Pipe
(Fig. 16)
The gun handle has a safety device preventing unwanted
activation of high-pressure pipe. This device can be put into
operation by leasing the handle and activating safety stop
between the trigger and the handle.
Connection of the Hose (Fig. 13)
The water supply connection is furnished with particle filter.
Never let the apparatus work without filter. The intervals for
checking and cleaning of the filters depend on the water
quality. If the water in the water mains contains impurity
articles, the filter shall be cleaned after every use because
otherwise the apparatus output will (considerably) fall and the
pump may be damaged.
The supply connection part for water supply has a form of a
(male) plug and shall be fastened with screw on the inlet to
water tank of the apparatus. Put the clamping element
(female) to the hose and then connect this element with the
part of supply connection in form of a plug. Connect the high-
pressure hose to the connection/discharge for high-pressure.
Release water and press the handle in form of a gun till the
water starts flowing from the pipe continuously. The water
temperature shall not exceed 40
Setting the Spraying Angle (Fig. 11)
Warning:
The protection against spraying away shall
always be properly set, otherwise it could be pushed in under
the influence of the high-pressure jet, and it may also cause
injury and damage.
You may chose from 4 different jets market by your colour
that may show various spraying angles.
0° jet (red):
This jet creates an extremely focused jet with very high
pressure force. It is suitable for particularly careful cleaning of
small areas. The jet is therefore applicable only on the areas
that can resist such a pressure, e.g. metal or concrete. Not
suitable for wood.
15° jet (yellow):
This jet creates a jet
15° wide, therefore it is especially
suitable for intensive cleaning of smaller areas. The jet can be
used only for areas that can resist such high pressure.
40° jet (white):
The jet creates a jet 40° wide, water pressure is medium
strong. This jet is suitable for cleaning larger areas and may
be used for most cleaning works.
Low-Pressure Jet (black):
This jet can be used for chemicals and cleaning agent's
application. It creates the lowest pressure.
Important warning: The high-pressure jet can damage the
lining, coating and pavement due to the type of material
or insufficient know-how. Therefore check first the effect
on a smaller area. If necessary the water pressure can be
changed by replacement of the jet or by reduction of the
engine output.
Connection of the Jet (Fig. 15)
Connect the jet with quick-coupling device to the water pipe
leading to the jet. By means of the quick-coupling the jets can
be replaced quickly and without any problems. After the jet is
connected, shift the safety collar back towards the gun, then
set the jet on the end of water pipe. Release the safety collar.
0
C..
The jet is firmly set in the required position. When replacing
the jet shift the safety collar back, remove the old jet and set
the new one.
Caution: Check always carefully if the jet has been set
correctly.
Caution: If the safety collar cannot be shifted back
without problems, the jet has not been correctly set.
Press the jet with strength into the corresponding hole,
because the safety collar will not return back by itself and
the jet will get out.
Cleaning Means (Fig. 8)
Use suitable tank with cleaning means determined for
pressure washing machines. Do not use rinsing means for
washing, they contain salt. Quality cleaning means for
pressure washing machines are recommended for this high-
pressure
cleaner.
vessel/canister. Most washing means for cars contain
combination of washing means and wax for chassis (wax-
washing means mixture). They are mostly dense, viscous
means. The viscosity (hence liquid density) of the cleaning
means usually increases in cold weather. We recommend to
solve this kind of washing means in hot water before pouring
it into the vessel. At combination of washing and wax means it
is recommended to prepare a solution before use. As basic
principle the ratio of the mixture 50:50 is recommended. Of
course, you can create a mixture with a different ration based
on testing, that may be more suitable for your purposes.
Instructions:
•
Dense cleaning means cannot flow properly
from the cleaning vessel and it can clog the
system with deposits.
•
The cleaning vessel shall be thoroughly rinsed
with water after use.
When using the delivered cleaning means the black jet (low
pressure) shall be fixed on the end of the water pipe. Insert
the end of the suction pipe into the cleaning means vessel of
the high-pressure cleaner. Suction and mixing of the cleaning
means will pass automatically if the water flows through the
pump.
Installation of High-Pressure Cleaner
•
Place the high-pressure cleaner on solid and even
surface in a way enabling properly lubrication of the
engine and the pump. When installing avoid the
places with depressions or holes (e.g. places with
puddles). When the surfaces are smooth and
slippery, there is danger of injury!
•
Place the apparatus on a well ventilated place in
sufficiently
materials or vapours. Safety regulations for proper
ventilation shall be principally observed. Minimum
distance from inflammable materials shall be 50
cm.
•
The apparatus shall be placed so that the operator
will have easy access to all parts thereof and to the
control elements. During installation the apparatus
shall be properly protected against the damages
from outside.
•
The high-pressure hose shall not be laid across the
traffic area, otherwise it may be worn very quickly
and damages may occur.
Putting the Apparatus into Operation
•
Remove dirt and foreign particles from the spray
gun and from the connection in form of a plug.
•
Put the jet on the spray gun.
•
Start the engine
Warning: The protection against spraying away shall
all the time be properly set, otherwise it could be
depressed by high-pressure jet, and damage and
injury may occur.
Start of the engine: (Fig. 14/20/17/21)
•
Turn the petrol cock (ON)
•
Open the choke (ON)
•
Set the engine switch on EIN/ON
17
Observe
the
instructions
safe
distance
from
inflammable
on
the
Publicité
Table des Matières
