Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Do not make any modifications to the autoSteady system (mechanical or electronic). This can be very
dangerous! No warranty claim will be accepted and we cannot warrant the function of the autoSteady
system if any modifications are made. We will not be liable for any damage whatsoever caused as a
result of incorrect installation, operation or modification.
OPERATION - REMOTE CONTROL HANDSET
The remote control handset (6) is powered by one PP3 9Volt battery, and is activated by moving the slide
switch to "On"-I (Fig. 10A). Once activated the green LED (Fig. 10I) will illuminate and the controls can now be
used.
Fig. 10
A.
Slide switch ("Off"=O and "On"=I)
B.
Up button including red LED
C.
Down button including red LED
D.
Automatic function button including red LED: auto set down or withdraw all the foot by automatic function
E.
Left-front single button: adjust left-front foot up or down
F.
Left-back single button: adjust left-back foot up or down
G.
Right-front single button: adjust right-front foot up or down
H.
Right-back single button: adjust right-back foot up or down
I.
Three colour LED: reflects status of the remote control and autoSteady system
A – Main power slide switch: "Off"=O and "On"=I.
B – Up button: Select the draw-back function for Auto function button or single corner steady function buttons.
After this button is pressed, the red LED in this button will light up. Then you can push the Auto function button
or single corner steady function buttons for draw back. Without choose "UP" (or "Down"), the Auto function
button or single corner steady function buttons are not workable. If there is not any operation within 30
seconds, the LED will turn off and invalidate the "UP" choice.
C – Down button: Select the lower function for Auto function button or single corner steady function buttons.
After pressing this button, the red LED in this button will light up. Then you can push the Auto function button
or single corner steady function buttons for lower. Without choose "Down"(or "UP"), the Auto function button or
single corner steady function buttons are not workable. If there is not any operation within 30 seconds, the LED
will turn off and invalidate "Down" choice.
D – Auto function button including red LED: automatically lower or draw back all of the corner steadies. If
you select the "DOWN" function, it applies the automatic lower. If you select the "UP" function, it applies the
automatically draw back.
The "AUTO" button must be pressed for more than 3 seconds. The red LED of the "AUTO" button will blink and
the buzzer also gives a beep per second. Then the automatic lower or draw back begins. If press it for less than
3 seconds, nothing happens (this is a setup to avoid misoperation).
After three seconds the automatic lower or draw back begins, and the red LED of the "AUTO" button will
illuminate constantly. Now you can release the button, and the lower or draw back will auto process. After the
automatic lower or draw back process is completed, the buzzer will give a beep.
Before the corner steadies move downwards, there maybe a several second delay without any operation or the
corner steady draw back a shorter time (about 3 seconds). This is normal.
E – Left-front single corner steady function button: Adjust Left-front corner steady (see Fig. 8) draw back
or lower by pressing the button. Choose the "UP" or "DOWN" button first.
F – Left-back single corner steady function button: Adjust Left-back corner steady (see Fig. 8) draw back
or lower by pressing the button. Choose the "UP" or "DOWN" button first.
G – Right-front single corner steady function button: Adjust Right-front corner steady (see Fig. 8) draw
back or lower by keep pushing the button. Choose the "UP" or "DOWN" button first.
H – Right-back single corner steady function button: Adjust Right-back corner steady (see Fig. 8) draw
back or lower by keep pushing the button. Choose the "UP" or "DOWN" button first.
I – Three colour LED for different messages.
The slide switch (Fig. 10A) also acts as an "Emergency stop".
EN
®
autoSteady 33
DURO
Ref: AS101-UM-TKI-1212-Rev. A
Publicité
Table des Matières
