Operation - Getting Started - Enduro autoSteady AS101 Manuel D'utilisateur

Jack-up force switch (Fig. 13E): The system is suitable for a big range of the caravans. To make sure that
the system is always working properly and your caravan is stable, the current protection can be adjusted via a
slide switch on the control unit (Fig. 13E).
L: Low current for caravans up to 1000kg
M: Normal current for caravans in the range of about 1000 – 1500kg
H: High current for caravans in the range of about 1500 – 2000kg
Different caravan chassis or floors have different situation for jack-up force. The above mentioned values are
just a rough indication. Please check what is the most convenient for your caravan so your caravan or caravan
chassis will not be damaged but still your caravan is stable.
The Reset Button (Fig. 13D): The remote control handset and the control unit are synchronised with each
other in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised
as described below:
Check the installation in accordance with the installation instructions. Check that the battery is properly
•
connected, check the condition of the battery and that a voltage of 12 V is present at the control unit.
Please ensure that the battery isolation switch is on.
•
Press the reset button (Fig. 13D) on the control unit for three seconds and then release it. The green LED
•
(Fig. 13A) starts blinking quickly (2Hz).
Activate the remote control by sliding the slide switch (Fig. 10A) to "On"-I. The green LED of the remote
•
control and the LED's of the "UP" and "DOWN" buttons (Fig. 10B & 10C) will illuminate continuously.
• Push both the "UP" and "DOWN" buttons (Fig. 10B & 10C) on the remote control at the same time for more
than 3 seconds. Then the handset buzzer will give a short beep to confirm that the synchronisation is
complete.
After successful synchronisation, the green LED on the control unit (Fig. 13A) and on the remote control
•
(Fig. 10I) will illuminate continuously.
After pressing the reset button on the control unit, if have not any operation in more than 15 seconds, the re-
synchronization process will stop.

OPERATION - GETTING STARTED

Please make sure you read the safety instructions very carefully and make sure that you
follow these guidelines!
Make sure that the battery that supplies the system is fully charged and in good condition.
Make sure that the caravan is free from the vehicle and the handbrake is on.
Before you can start using the autoSteady system, please make sure you caravan is already levelled out in all
directions. Please use the supplied tool (3) and accomplish this the usual way.
Just as the standard corner steady of your caravan can only be used for stabilising, also the
autoSteady system cannot be used for jacking up or levelling out your caravan.
Once the caravan is levelled out, you can start using the autoSteady system.
Turn on the battery power isolation switch (24).
Activate the autoSteady system by moving the slide switch to "On"-I on the remote control (Fig. 10A). The
green LED (Fig. 10I) will illuminate continuously. The system is ready for use.
During the operation of the system, the handbrake must be secured.
First press the "DOWN" (Fig. 10C) button. The red LED in this button will illuminate.
Press for at least three seconds the "AUTO" button (Fig. 10D). The green LED (Fig. 10I) will blink during these
three seconds and every second there will be a beep. This is warning you that the system will be activated.
After these three seconds the auto function will start and the corner steadies will automatically act. The green
LED on the remote control will illuminate continuously. Now you can release the AUTO button.
The corner steady will act as following:
first the two back corner steadies (Fig. 8B and Fig. 8D) lower
•
• then the two front corner steadies (Fig. 8A and Fig. 8C) lower
than the back corner steadies (Fig. 8B and Fig. 8D) lower again
•
finally the two front corner steadies (Fig. 8A and Fig. 8C) lower again
•
EN ® autoSteady 35
DURO
Ref: AS101-UM-TKI-1212-Rev. A