Operation - Remote Control Handset; Operation - Electronic Control Unit - Enduro EM203 Manuel D'utilisateur

OPERATION - REMOTE CONTROL HANDSET

The remote control handset (31) is powered by one PP3 9Volt battery, and is activated by double-pressing the
red button (Fig. 5A). Once activated the red LED (Fig. 5H) will illuminate and the directional controls can now
be used.
Fig. 5
A = On (press button twice within one second, red LED illuminates)
B = Caravan forwards (both wheels rotate in forwards direction)
C = Caravan reverse (both wheels rotate in reverse direction)
D = Caravan left forwards (right wheel rotates in forwards direction)
E = Caravan right forwards (left wheel rotates in forwards direction)
F = Caravan left reverse (right wheel rotates in reverse direction)
G = Caravan right reverse (left wheel rotates in reverse direction)
In addition, the 'left forward' (E) and 'right reverse' (F) buttons or 'right forward' (D) and 'left reverse' (G)
buttons may be pressed at the same time to turn the caravan around on its own axis (without moving forward
or backward).
When you switch within 2 seconds from forward driving to reverse driving (and the other way around), a small
delay of 1 second will appear to protect the electronics and the motors.
If the handset has not been used for a period of 180 seconds then it will automatically switch itself off.
Changing batteries in the remote control:
When the battery is empty, it needs to be replaced.
x
Open the rear cover of the handset (Fig. 7A).
x
Take out the dead/old battery and dispose in the appropriate way.
x
Install a new replacement battery (Fig. 7.1). Make sure to use a leak proof PP3 (9Volt) battery (No claims
under guarantee can be considered for damage caused by leaking batteries).
x
Close the rear cover again.
Dead and used batteries may leak and damage the remote control handset! Remove the batteries if the
handset is not going to be used for an extended period.

OPERATION - ELECTRONIC CONTROL UNIT

The Electronic Control Unit (32), which is mounted inside your caravan, is responsible for controlling the
®
enduro manoeuvring system.
The control unit has three LED's and one button (Fig. 3):
Green LED (Fig. 3B): Power LED continuously illuminated when system is activated (press red button twice
within one second). If the handset far away from the control unit, beyond the availably distance, this LED will
go out.
Blue LED (Fig. 3C): Error message LED concerning caravan battery:
x
Blue LED is blinking (2Hz, 2 times blinking, break, 2 times blinking, break etc.): Battery voltage too low
(<10V). Battery needs to be recharged.
x
Blue LED is blinking (2Hz, 4 times blinking, break, 4 times blinking, break etc.): Battery Voltage too high
(over charged). Try to discharge the battery by turning on a user (for example a lamp or water-pump).
Red LED (Fig. 3D) is blinking (2Hz, 6 times blinking, break, 6 times blinking, break etc.): Amp overload
protection is activated. Wait about 60 seconds and try again.
In general all error messages will reset automatically after one minute. If this is not the case, reset the
electronics of the manoeuvring system by switching off the system via the isolation switch and the remote
control handset for at least 15 seconds and then turning it on again.
The Reset Button (Fig. 3A): The remote control handset and the control unit are synchronised with each other
in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised as
described below:
x
Check the installation in accordance with the installation instructions and ensure that the drive rollers are
not applied. Check that the battery is properly connected, check the condition of the battery and that a
voltage of 12 V is present at the control unit.
x
Please ensure that the battery isolation Switch is on.
x
Press the reset button (Fig. 3A) on the control unit and hold down. The green LED (Fig. 3B) flashes slowly.
x
Activate the remote control handset by pressing the red button twice within one second (Fig. 5A). The
green LED on the control unit (Fig. 3B) starts to flash rapidly. The remote control handset and the control
®
enduro EM203 29
Ref: EM203-UM-EAL-0211-Rev.D.