Inspect Your Shipment - Franklin Electric C1 Serie Manuel Du Propriétaire

Wire motor for correct voltage. See
WA R N I N G
"Electrical Installation" section of this
manual and motor nameplate. The
C1-Series is available to operate on
either 230V or 115V input power.
Check product nameplate to
determine correct input voltage.
Ground motor before connecting
to power supply. Pump is supplied
Hazardous voltage.
with a copper ground wire. Use only
Can shock, burn, or
copper wire for pump connection.
cause death.
DO NOT GROUND PUMP TO A
Ground pump before
connecting to power
GAS SUPPLY LINE.
supply. Disconnect
power before working Meet National Electrical Code (NEC)
on pump, motor or tank
or Canadian Electrical Code (CEC) and
local codes for all wiring.
Follow all pump wiring instructions
provided in this manual.
AT T E N T I O N
IMPORTANT INFORMATION FOR INSTALLERS OF THIS EQUIPMENT!
THIS EQUIPMENT IS INTENDED FOR INSTALLATION BY
TECHNICALLY QUALIFIED PERSONNEL. FAILURE TO INSTALL IT
IN COMPLIANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES,
AND WITHIN FRANKLIN ELECTRIC RECOMMENDATIONS, MAY
RESULT IN ELECTRICAL SHOCK OR FIRE HAZARD, UNSATISFACTORY
PERFORMANCE, AND EQUIPMENT FAILURE. FRANKLIN
INSTALLATION INFORMATION IS AVAILABLE FROM PUMP
MANUFACTURERS AND DISTRIBUTORS, AND DIRECTLY FROM
FRANKLIN ELECTRIC. CALL FRANKLIN TOLL FREE 800-348-2420
FOR INFORMATION.
WA R N I N G
SERIOUS OR FATAL ELECTRICAL SHOCK MAY RESULT FROM
FAILURE TO CONNECT THE INLINE SYSTEM, METAL PLUMBING,
AND ALL OTHER METAL NEAR THE C1-SERIES SYSTEM OR CABLE,
TO THE POWER SUPPLY GROUND TERMINAL USING WIRE NO
SMALLER THAN MOTOR CABLE WIRES. TO REDUCE RISK OF
ELECTRICAL SHOCK, DISCONNECT POWER BEFORE WORKING
ON OR AROUND THE WATER SYSTEM. DO NOT USE C1-SERIES
SYSTEM IN SWIMMING AREAS.
General Safety
The Franklin Electric C1-Series cistern pumping system is designed
and approved for use in effluent pumping applications. Do not
allow pump or any system plumbing to freeze. To do so will void
the warranty.
This pump has been evaluated for pumping water only. Pumping
liquids other than water may void warranty. Periodically inspect
pump and system components.
C1-Series KEY FEATURES
Pump Features:
• Available in 10, 20, and 30 gallons per minute (gpm).
• All pumps are powered by a high quality 0.5 hp
submersible motor.
• 1.25-inch NPT pump outlet.
• Bottom suction design to allow for the unit to pump longer
and more reliably without losing its prime.
• Available in both 115V and 230V options.
• Motor protected thermally by a built in overload.
• Built for long life in gray water and effluent pumping
applications.
• Stainless steel and precision molded industry standard
thermal plastic construction for all wetted surfaces.
• 10' SJOOW power cord designed specifically for
effluent pumping.
• Supplied with a removable 5" base for secure and reliable
mounting.

INSPECT YOUR SHIPMENT

All Franklin Electric C1-Series are carefully tested, inspected, and
packaged to insure their arrival in perfect condition. When the
pump is received, examine it closely to make sure there is no
damage that may have occurred in shipping. If damage is evident,
report this immediately to your shipping carrier and product
dealer. The shipping carrier assumes full responsibility for the
shipment's safe arrival. Any claim for damage to the shipment,
either visible or concealed, must be made through the shipping
carrier first.
INSTALLATION
Location Of The C1-Series Pump
The C1-Series is designed to be installed in a cistern gray water/
effluent environment. The pump should be protected to prevent
possible freezing.
If a sewage tank is near or a part of the system where the C1-Series
pump is installed, proper ventilation is required to meet all local
and national codes.
NOTICE: READ AND FOLLOW ALL INSTRUCTIONS!
Disconnect power at electrical panel before making any
electrical connections.
Adhere to the guidelines of national, state and local
plumbing codes when installing this product. Check with
the appropriate agencies or water systems professional for
additional information.
Supply voltage must be +/- 10% of motor nameplate
voltage. Low or high voltage can damage the motor and
will void the warranty.
If possible, connect pump to dedicated branch circuit with
no other appliances on it.
Do not operate pump unless pump is grounded.
Solder and tape all spliced connections carefully. A fused
disconnect switch or circuit breaker should be placed at or
near the pump.
3