Extended Menu - Comunello Automation CU-24V-HP Instructions D'utilisation Et D'installation

Warning: Automatic Programming is not available without limit
switches.

EXTENDED MENU 1

The control unit is factory set to allow direct selection exclusively of the
main menu functions. If you wish to enable the functions described in
Extended Menu 1, proceed as follows: select blinking LEV LED and
press SET once. The LED will start blinking. This means there will be 30
seconds to select the functions of Extended Menu 1 using the SELECT
and SET keys; once an additional 30 seconds have elapsed the control
unit reverts to the main menu.
L1 HOLD-TO-RUN
L2 PEDESTRIAN / SINGLE LEAF
PUSHBUTTON
L3 PEDESTRIAN PUSHBUTTON / DS3
L4 FOTOTEST
L5 DS2 STP IN CLOSING
L6 DS1 PARTIAL REVERSAL
L7 NC AS 8K2
LEV MENU LEVEL
1. HOLD-TO-RUN:
The control unit allows to set the "Hold-to-run" function. If you wish
to enable the function, proceed as follows: ensure you have enabled
Extended Menu 1 (alternate blinking 1 0 1 0 1 0 of LED LEV) and then
use the SEL key to select blinking LED L1 and press the SET key; LED
L1 becomes steady on and the operation will be completed. With hold-
to-run enabled, using either the remotes or the Pushbuttons to operate
the gate, the following operation will be obtained: the command must be
maintained constantly to move the gate. When the command is released
movement will stop immediately. Repeat the procedure if you wish to
restore the previous configuration.
2. SINGLE LEAF OR PED. BUTTON = OPEN, PED. BUTTON =
CLOSE:
The control unit allows a NO Pushbutton to be connected (CN2 input
no. 10) to activate the gate in Pedestrian Opening mode. It is however
possible to use this input to connect a NO pushbutton operating in a
different manner. If you wish to enable the "Single Leaf" function, proceed
as follows: ensure you have enabled Extended Menu 1 (alternate blinking
1 0 1 0 1 0 of LED LEV) and then use the SEL key to select blinking LED
L2 and press the SET key; LED L2 becomes steady on and the operation
will be completed. With this function enabled the Pushbutton can be used
to activate exclusively Operator 1 (refer to the heading "Single Leaf"). In
contrast, if you wish to enable "OPEN-CLOSE" mode in order to use the
Pedestrian Pushbutton to control exclusively opening of the gate and the
P/P Pushbutton to (CN2 input no. 11) to control exclusively closing of the
gate, repeat the operation described above, pressing the SEL key twice
(LED L2 will blink rapidly) rather than just once. Repeat the procedure if
you wish to restore the initial configuration.
3. PEDESTRIAN PUSHBUTTON / DS3:
The control unit allows a NO Pushbutton to be connected (CN2 input
no. 10) to activate the gate in Pedestrian Opening mode. However, this
input can be used to connect a DS3 photocell (NC): make sure you have
enabled Extended Menu 1 (alternate blinking 1 0 1 0 1 0 of LED LEV) and
then use the SEL key to select blinking LED L3 and press the SET key;
LED L3 becomes steady on and the operation will be completed. Repeat
the procedure if you wish to restore the previous configuration.
4. FOTOTEST (Photocells test):
The control unit is factory set with the photocells test disabled. If you
wish to enable the photocells test proceed as follows: ensure you have
enabled Extended Menu 1 (blinking 1 0 1 0 1 of LED LEV) and then use
the SEL key to select blinking LED L4 and press the SET key; LED L4
becomes steady on and the operation will be completed. Repeat the
procedure if you wish to restore the previous configuration.
5. DS2 STOP DURING THE CLOSING CYCLE:
The control unit allows the operation of input DS2 to be modified. If
you want DS2 to trip also during closing (stopping of the gate leaf). If
in Automatic operating mode and once the passage is free closing
movement of the gate is resumed, proceed as follows: ensure you have
enabled Extended Menu 1 (alternate blinking 1 0 1 0 1 0 of LED LEV) and
26
COMUNELLO ®Copyright 2014 - All right reserved
ON OFF
SINGLE LEAF PEDESTRIAN PUSHBUTTON
DS3 PEDESTRIAN PUSHBUTTON
ON OFF
ON OFF
ON OFF
ON OFF
1 FLASH
then use the SEL key to select blinking LED L5 and press the SET key;
LED L5 becomes steady on and the operation will be completed. Repeat
the procedure if you wish to restore the initial configuration.
6. DS1 PARTIAL REVERSAL:
The control unit allows the operation of input DS1 to be modified. If you
want DS1 to cause a partial reversal (short reversal) of the gate leaf
instead of a total reversal, proceed as follows: ensure you have enabled
Extended Menu 1 (alternate blinking 1 0 1 0 1 0 of LED LEV) and then
use the SEL key to select blinking LED L6 and press the SET key; LED
L6 becomes steady on and the operation will be completed. Repeat the
procedure if you wish to restore the initial configuration.
7. EMERGENCY STOP = 8K2:
The control unit allows the connection of a NC Emergency Stop
pushbutton (CN2 input no.8). However, this input can be switched to an
8.2 KOhm resistive input: ensure you have enabled Extended Menu 1
(alternate blinking 1 0 1 0 1 0 of LED LEV) and then use the SEL key to
select blinking LED L7 and press the SET key; LED L7 becomes steady
on and programming will be completed. A change of the value read on
the input will cause the control unit to shut down irrespective of the gate
movement currently in progress. An additional gate movement command
will be valid provided the correct input value is restored and irrespective
of the prior status the control unit will execute the gate opening cycle.
Repeat the procedure if you wish to restore the initial configuration.
EXTENDED MENU 2
The control unit is factory set to allow direct selection exclusively of the
main menu functions.
If you wish to enable the functions described in Extended Menu 2,
proceed as follows: select blinking LED no.8 and press SET twice. The
LED will start blinking alternately 1 1 0 1 1 0. This means there will be 30
seconds to select the functions of Extended Menu 2 using the SEL and
SET keys; once an additional 30 seconds have elapsed the control unit
reverts to the main menu.
L1 BRAKE
L2 DECELERATION
L3 ALWAYS CLOSE
L4 FOLLOW ME
L5 PEDESTRIAN TIME
L6 2°CH MONOSTABLE
L7 REMOTE PROG.
LEV MENU LEVEL
1. BRAKE
The control unit is factory set with the electronic brake function disabled.
If you wish to enable this function, proceed as follows: ensure you have
enabled Extended Menu 2 (alternate blinking 1 1 0 1 1 0 1 1 0 of LED LEV)
and then use the SEL key to select blinking LED L1 and press the SET
key; LED L1 becomes steady on and the operation will be completed.
With the brake enabled the control unit reduces coasting of the gate due
to inertia at the time of a stop or direction reversal command. Repeat the
procedure if you wish to restore the previous configuration.
2. DECELERATION:
As indicated above, the control unit allows a deceleration stage to be
programmed during opening and closing, while with the Automatic
Programming function the deceleration stage is included automatically.
However, if no deceleration is required it can be excluded. In this manner,
when using Automatic Programming the Deceleration stage will no longer
be included, while if the Motor Times Programming function is used the
option of programming a deceleration stage during opening and closing
will no longer be available. If, before excluding the deceleration stage
it had already been programmed using the Motor Times Programming
function, programming must be repeated from the beginning. If you wish
to exclude the deceleration stage proceed as follows: ensure you have
enabled Extended Menu 2 (blinking 1 1 0 1 1 0 of LED LEV) and then
use the SEL key to select blinking LED L2 and press the SET key; LED
L1 becomes steady on and the operation will be completed. Repeat the
procedure if you wish to restore the previous configuration.
3. ALWAYS CLOSE:
The control unit allows setting "Always Close" operation: this function,
ON OFF
OFF ON
ON OFF
ON OFF
ON OFF
ON OFF
ON OFF
2 FLASHES