Comunello Automation CU-24V-HP Instructions D'utilisation Et D'installation page 28

function enabled the sliding gate can be opened using the commands
from the P/P Pushbutton and the remotes, and the pedestrian gate can be
opened by activating the electric lock via the PED commands. To enable
this function proceed as follows: ensure you have enabled Extended
Menu 3 (blinking 1 1 1 0 1 1 1 0 of LED LEV) and then use the SEL key to
select blinking LED L5 then press the SET key; LED L5 becomes steady
on and programming will be completed. Repeat the procedure if you wish
to restore the previous configuration.
6. FLASHING LIGHT OPERATION/COURTESY LIGHT:
The control unit is factory set with Flashing Light during Pause Time
disabled. If you wish to enable this function proceed as follows: ensure
you have enabled Extended Menu 3 (blinking 1 1 1 0 1 1 1 0 of LED LEV)
and then use the SEL key to select blinking LED L6 and press the SET
key; LED L6 becomes steady on and programming will be completed.
Repeat the procedure if you wish to restore the previous configuration.
Courtesy Light Operation: The 24 Vac 4W max. Courtesy Light output
will switch on for 3 minutes whenever an opening command is transmitted
7. PREFLASHING/PAUSE FLASHING:
The control unit is factory set with the Preflashing and Pause Flashing
functions disabled. If you wish to enable the Preflashing function, proceed
as follows: ensure you have enabled Extended Menu 3 (blinking 1 1 1 0
1 1 1 0 of LED LEV) and then use the SEL key to select blinking LED L7
and press the SET key LED L7 becomes steady on and programming will
be completed. If you wish to enable the Pause Flashing function repeat
the operation described above, pressing the SET key twice (LED L7 will
blink rapidly) rather than once. Repeat the procedure if you wish to restore
the initial configuration.
Preflashing Operation: The 230 Vac and 24V flashing light output will
always switch on 3 seconds before the gate starts the closing operation..
Pause Flashing Operation: The 230 Vac and 24V Flashing Light output
will switch on if previously programmed The Pause Time.
RESET:
If it becomes necessary to reset the control unit to restore the factory
settings, press the SEL and SET keys together; this will cause all the RED
indicator LEDs to light simultaneously followed immediately by the control
unit switching off.
DIAGNOSTICS:
Photocell Test:
The control unit is prearranged for connection of safety devices in
compliance with standard EN 12453 point 5.1.1.6. At each operating
cycle a functional test of the connected photocell is performed. In the
case of an open circuit and/or malfunctioning of the photocell, the control
unit does not enable movement of the gate and visually signals the test
failed condition by causing all the indicator LEDs to blink simultaneously.
As soon as correct operation of the photocell is restored the control unit
is ready for normal use. This operating mode guarantees failure mode
monitoring in compliance with EN 954-1 Category 2.
Commands input test:
In correspondence with each low voltage command input the control unit
is equipped with an indicator LED so that the status of the input can be
checked at a glance.
Operating logic: LED on input closed, LED off input open.
WARRANTY
Fratelli Comunello SpA provides a warranty for 24 months for the correct
functioning of the actuators from the date of manufacture, provided that
the performance specications indicated in the product instruction manuals
are respected. Free of charge repair and replacement of components
that are found to be faulty according to the indisputable judgment of the
company's technical staff shall be guaranteed at the sole discretion of
Fratelli Comunello Spa, and so excluding any claim for damages made
by others. Warranty material shall be returned to Fratelli Comunello S.p.a.
headquarters carriage paid and will then be shipped to the customer
carriage unpaid. The material found to be faulty and returned to Fratelli
Comunello S.p.a. shall remain property of the Seller. Any cost resulting
from any work needed to repair the defect or to replace the material shall
be charged to the Buyer. No compensation shall be allowed for the period
of device inactivity. Work under warranty does not prolong the warranty
period. The defect of the product shall be reported by the Buyer within 8
(eight) days from its discovery or from the date of delivery of the goods,
28
COMUNELLO ®Copyright 2014 - All right reserved
under penalty of invalidation of the warranty. Such claim shall be notied
in writing.
Warranty does not cover:
Any product defect or damage that may have been incurred during
transport; any defect or damage arising from any fault and/or from
neglect, inadequacy and misuse of the electrical wiring in the Buyer's
property; any defect or damage caused by any repairs carried out by
non authorised personnel or by incorrect use/installation (with reference
to this, system maintenance is recommended every 6 months) or if
not original spare parts are used; any defect caused by chemicals or
atmospheric conditions. The warranty does not cover any cost neither
for consumable materials nor for alleged defects or convenient surveys.
Product Features Fratelli Comunello SpA products are subjected to
continue changes and improvements; their technical features and image
may therefore change without previous notice.
Competent court
Since the contract of sale is conrmed by an Order Conrmation drawn up
in Rosà, any such dispute shall be settled by the laws of Italy and by the
court of Vicenza (VI).