Moser 1233 Manuel D'utilisation page 13

Operation
Preparation
Keep the packaging material for safe storage or
transport later.
f Check that the contents are complete.
f Check all the parts for possible transport damage.
Safety
Caution! Damage due to incorrect power
supply.
f Only operate the appliance with the voltage
stated on the nameplate.
Mains operation
1. Oil the blade set (Fig. 7).
2. Insert the mains plug into the mains socket.
3. Switch on the appliance using the on/off switch
(Fig. 2ⓐ) and, after use, switch it off again (Fig. 2ⓑ).
Operation
Cutting length adjustment
Without the attachment comb, the normal cutting
length of the appliance is approx. 0.1 mm.
The cutting length can be adjusted between 0.1 and 3 mm,
even when the appliance is in use.
1. Slide the locking switch downwards (Fig. 3ⓐ).
2. Operate the side cutting length adjustment lever
(Fig. 4ⓐ). You can set the cutting length to 6 pre-set
positions (MultiClick).
3. Slide the locking switch upward to unlock the setting
(Fig. 3ⓑ). The normal cutting length of approx. 0.1 mm
is restored.
Cutting with attachment combs (depending on model)
The appliance can also be operated with attachment
combs.
f For this, the cutting length adjustment lever (B) must
not be locked (Fig. 4ⓑ).
f Slide the locking switch (F) upward to unlock (Fig.3 ⓑ).
· Depending on the model, various attachment
combs are included in the scope of supply.
· Attachment combs #1 (4.5 mm), #2 (6 mm),
#3 (9 mm), #4 (14 mm), #5 (19 mm) and an
adjustable attachment comb (4 - 18 mm) are
also optionally available as accessories.
Attaching/removing the attachment comb
1. Slide the attachment comb on to the blade set in the
direction of the arrow until it reaches the limit stop
(Fig. 5ⓐ).
2. The attachment comb can be removed by pushing it in
the opposite direction (Fig. 5ⓑ).
Maintenance
Warning! Injuries and material damage due to
incorrect handling.
f Switch off the appliance before cleaning it or
performing any maintenance. Disconnect the
appliance from the power supply.
Cleaning and care
Danger! Electric shock due to penetration of
liquid.
f Do not immerse the appliance in water!
f Do not allow any liquid to get inside the
appliance.
f Only reconnect the appliance to the power
supply if it is completely dry.
Caution! Danger from aggressive chemicals.
Aggressive chemicals could damage the appli-
ance and accessories.
f Never use solvents or scouring agents.
f Only use cleaning agents and blade set oil
recommended by the manufacturer.
Accessories and spare parts are available from
your dealer or our service centre.
f Remove the attachment comb (Fig. 5ⓑ) after every
use. Remove the hair clippings from the blade set with
the cleaning brush.
If thorough cleaning is required, (Fig.6) the blade
set can be removed. See chapter Changing the
blade set.
f After cleaning the blade set, we recommend using
hygienic spray. It keeps all blade sets hygienically
clean.
f Oil the blade set with the blade set oil (Fig. 7).
f We recommend that you clean and care for your blade
set during and after clipping with Blade Ice spray. The
Blade Ice spray ensures instant cooling, oiling and
cleaning of the blade set, while also protecting against
corrosion.
f Switch the appliance on briefly (approx. 10 sec.) to
ensure the oil film is evenly distributed.
f For a good and long-lasting cutting perfor-
mance, it is important to oil the blade set
frequently.
f If the cutting performance deteriorates after
long use despite regular cleaning and oiling,
the blade set should be replaced.
f Only wipe the appliance with a soft, slightly damp cloth.
ENGLISH
de
en
fr
it
es
pt
nl
da
sv
no
fi
tr
pl
cs
sk
hr
hu
sl
ro
bg
ru
uk
et
lv
lt
el
ar
13