Uk Declaration Of Conformity; Noise And Vibration Declaration Statement - Desoutter ERP250 Mode D'emploi

Safety Information

UK Declaration of Conformity

We Ets Georges Renault, 38 rue Bobby
Sands, 44818 Saint Herblain, France, declare
under our sole responsibility that the product
(with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
• Electromagnetic Compatibility Regulations
2016
• Supply of Machinery (Safety) Regulations
2008
• The Restriction of the Use of Certain Haz-
ardous Substances in Electrical and Elec-
tronic Equipment Regulations 2012
Designated Standards applied:
EN 62841-2-2:2014 + AC1:2015 EN 61000-3-2:2019 EN
61000-3-3:2013+A1:2019 EN 61000-6-2:2019
EN61000-6-4:2019 EN 61326-2-3:2013 EN 62311:2008
Authorities can request relevant technical information from:
Pascal ROUSSY, R&D Manager, 38 rue Bobby Sands,
44818 Saint Herblain, France
Saint-Herblain, 2022/02/03
Pascal ROUSSY, R&D Manager
Signature of issuer
Authorities can request relevant technical information from:
UK Authorized Representative:
Air Compressors & Tools Ltd
Zodiac – Unit 4, Boundary way
Hemel Hempstead Industrial Estate, HP27SJ Hempstead
Hertfordshire – UK
Contact: M.Taylor

Noise and Vibration Declaration Statement

• Sound power level < 75 dB(A) , uncertainty 3 dB(A), in
accordance with EN 62841-2-2:2015 + AC1:2015.
• Vibration total value < 2.5 m/s
accordance with EN 62841-2-2:2015 + AC1:2015.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. The vibration emis-
sion level may be used for a preliminary assessment of expo-
sure. These declared values are not adequate for use in risk
assessments and values measured in individual work places
may be higher. The actual exposure values and risk of harm
experienced by an individual user are unique and depend
upon the way the user works, the workpiece and the worksta-
tion design, as well upon the exposure time and the physical
condition of the user.
2 2
, uncertainty 3 m/s , in
4 / 144
We, Ets Georges Renault, cannot be held liable for the con-
sequences of using the declared values, instead of values re-
flecting the actual exposure, in an individual risk assessment
in a work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
www.pneurop.eu/index.php
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE directive/regulations (2012/19/EU), and must be
handled in compliance with the directive/regulations.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE directive/regulations. The
entire product, or the WEEE parts, can be sent to your "Cus-
tomer Center" for handling.
FCC compliance Class A
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user's authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this de-
vice must accept any interference received, including inter-
ference that may cause undesired operation.
FCC Responsible party:
Name: Mark Johnson
Position: General Manager
Address: Chicago Pneumatic Tool Company
LLC 1815 Clubhouse Road Rock Hill
SC 29730
USA
Mobile: +1 800 624 4735
Email: mark.johnson@desouttertools.com
http://
and selecting 'Tools' then 'Legis-
04/2022