Uk Declaration Of Conformity; Noise And Vibration Declaration Statement - Desoutter Industrial Tools ELB2.5-1250-P Mode D'emploi

UK Declaration of Conformity

We Ets Georges Renault, 38 rue Bobby
Sands, 44818 Saint Herblain, France, declare
under our sole responsibility that the product
(with name, type and serial number, see front
page) is in conformity with the following UK
Regulation(s):
Electromagnetic Compatibility Regulations 2016
Supply of Machinery (Safety) Regulations 2008
The Restriction of the Use of Certain Hazardous Sub-
stances in Electrical and Electronic Equipment Regula-
tions 2012
Radio Equipment Regulations 2017
Designated Standards applied:
For ELB, ELS series
EN 62841-2-2:2014+C1:2016; EN
61000-6-2:2005+C1:2005; EN 61000-6-3:2007+A1:2011;
EN 55014-1:2017; EN 55014-2:2015; EN 62311:2008
For ELC series
EN 62841-2-2:2014+C1:2016; EN
61000-6-2:2005+C1:2005; EN 61000-6-4:2007+A1:2011;
EN 55014-1:2017; EN 55014-2:2015; EN 301 489-17
V3.2.2; EN 300 328 V2.2.2; EN 301893 V2.1.1; EN 300
440 V2.2.1
Saint-Herblain, 2022/01/31
Pascal ROUSSY, R&D Manager
Signature of issuer
Authorities can request relevant technical information from:
UK Authorized Representative:
Air Compressors & Tools Ltd
Zodiac – Unit 4, Boundary way
Hemel Hempstead Industrial Estate, HP27SJ Hempstead
Hertfordshire – UK
Contact: M.Taylor

Noise and Vibration Declaration Statement

• Sound power level 72 dB(A) , uncertainty 3 dB(A), in
accordance with EN 62841-2-2 : 2014.
• Vibration total value < 2.5 m/s
accordance with EN 62841-2-2 : 2014.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. The vibration emis-
sion level may be used for a preliminary assessment of expo-
sure. These declared values are not adequate for use in risk
assessments and values measured in individual work places
04/2022
2 2
, uncertainty 3 m/s , in
5 / 208
may be higher. The actual exposure values and risk of harm
experienced by an individual user are unique and depend
upon the way the user works, the workpiece and the worksta-
tion design, as well upon the exposure time and the physical
condition of the user.
We, Ets Georges Renault, cannot be held liable for the con-
sequences of using the declared values, instead of values re-
flecting the actual exposure, in an individual risk assessment
in a work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
www.pneurop.eu/index.php
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE directive/regulations (2012/19/EU), and must be
handled in compliance with the directive/regulations.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE directive/regulations. The
entire product, or the WEEE parts, can be sent to your "Cus-
tomer Center" for handling.
Information Regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that cer-
tain electrical and mechanical components in the product
may contain lead metal. This is in compliance with current
substance restriction legislation and based on legit exemp-
tions in the RoHS Directive (2011/65/EU). Lead metal will
not leak or mutate from the product during normal use and
the concentration of lead metal in the complete product is
Safety Information
http://
and selecting 'Tools' then 'Legis-