Desoutter ERP250 Mode D'emploi page 5

NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device, pur-
suant to Part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference when the equipment is operated in a com-
mercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruction man-
ual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense. Any changes or modifications to this
equipment not expressly approved by Desoutter may
cause, harmful interference and void the FCC authoriza-
tion to operate this equipment.
IC compliance Class A
CAN ICES-3(A)/NMB-3(A)
(English) This device complies with Innovation, Science and
Economic Development Canada's licence-exempt RSSs. Op-
eration is subject to the following two conditions:
1) This device may not cause interference
2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Inno-
vation, Sciences et Développement économique Canada ap-
plicables aux appareils radio exempts de licence. L'exploita-
tion est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage
2) l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromet-
tre le fonctionnement
Information Regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that cer-
tain electrical and mechanical components in the product
may contain lead metal. This is in compliance with current
substance restriction legislation and based on legit exemp-
tions in the RoHS Directive (2011/65/EU). Lead metal will
not leak or mutate from the product during normal use and
the concentration of lead metal in the complete product is
well below the applicable threshold limit. Please consider lo-
cal requirements on the disposal of lead at product end of
life.
04/2022
Regional Requirements
WARNING
This product can expose you to chemicals including
lead, which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For
more information go to
https://www.p65warnings.ca.gov/
Safety
DO NOT DISCARD - GIVE TO USER
WARNING Read all safety warnings, instructions, il-
lustrations and specifications provided with this
product.
Failure to follow all instructions listed below may result
in electric shock, fire, property damage and/or serious
injury.
Save all warnings and instructions for future refer-
ence.
WARNING All locally legislated safety rules regard-
ing installation, operation and maintenance shall be
respected at all times.
Statement of Use
• For professional use only.
• This product and its accessories must not be modified in
any way.
• Do not use this product if it has been damaged.
• If the product data or hazard warning signs on the prod-
uct cease to be legible or become detached, replace with-
out delay.
• The product must only be installed, operated and ser-
viced by qualified personnel in an industrial environ-
ment.
Intended Use
This product is designed for installing and removing threaded
fasteners in wood, metal or plastic. Indoor use only.
No other use permitted.
Product Specific Instructions
Product description
2
1
7
8
1 Output
2 Direction selector
5 / 144
Safety Information
3
4
5
6