GYS GYSPOT PTI GENIUS Manuel D'utilisation page 59

Raison sociale : JBDC
Adresse :
ZI, 134 Bd des Loges
Code postal :
53941
Ville :
Saint-Berthevin
Intervenant : OPERATEUR
Ordre de réparation : 977AC92
Date du journal : 05/04/2018
Intervention : AILE ARRIERE
Commentaires : Commentaires
GYSPOT BP.LG (1712009013)
Id Date Mode Outil
1 05/04/18 10:22 Auto Pince en C n°1
2 05/04/18 10:22 Auto Pince en C n°1
3 05/04/18 10:22 Auto Pince en C n°1
4 05/04/18 10:22 Auto Pince en C n°1
5 05/04/18 10:22 Auto Pince en C n°1
6 05/04/18 10:23 Normal Pince en C n°1
7 05/04/18 10:23 Normal Pince en C n°1
8 05/04/18 10:23 Normal Pince en C n°1
9 05/04/18 10:23 Normal Pince en C n°1
10 05/04/18 10:23 Normal Pince en C n°1
11 05/04/18 10:23 Manuel Pince en C n°1
SAFETY AND MAINTENANCE
User training
People operating this machine must receive suitable training in order to get the most out of the machine capabilities and carry out good quality repairs
(examples: car body work training).
Preparation of the parts to be assembled
It is essential to clean and accost the area to be welded.
In the case of a protective application, make sure that it is conductive by first testing a sample.
Monopoint electrode welding
When repairing a vehicle, check that the manufacturer allows this type of welding process.
Using the underwing arm
The maximum pressure is 100 daN.
O-rings for the locking nuts of G arm.
Inside the 2 arm locking nuts, there are 2 O-rings that must be replaced in case of a leak or every 6 months. These 2 seals are necessary to avoid
any risk of leakage.
These seals are O-rings d=25, group of 4. When replacing these seals, grease must be applied to them. (ref. 050440 : contact grease)
Quantity and quality of the coolant
The coolant level is important for the correct operation of the machine. It must always be between the minimum and maximum level indicated on the
trolley. Top up with demineralized water if necessary.
Replace the coolant every 2 years :
1 Switch off the power supply using the switch located at the rear of the machine (OFF position) and disconnect the unit from the mains.
2 Place a bucket (min. 30 l capacity) under the machine drain hole.
3
4 Rinse the inside of the tank with running water to remove deposits.
5
Replace the drain plug. (
6 Fill the tank with coolant (5l : 062511 / 10l : 052246)
7 Turn the power back on (ON position) and check for leaks.
GYSPOT PTI GENIUS
0243510101
Téléphone :
Télécopie :
0243510102
Email :
contact@companyname.com
Site Web : www.companyname.com
Marque : PEUGEOT
Modèle : 308SW
N° châssis : 12365849
Immatriculation : 1450UT53
Mise en circulation : 01/01/2017
Consignes Mesures
Temps Serrage Serrage
Intensité (kA) Intensité (kA)
(ms) (daN) (daN)
630 9,4 325 9,4 325
630 9,4 325 9,3 325
490 8,2 240 8,2 240
510 8,3 250 8,2 245
510 8,3 250 8,3 245
350 7,3 225 7,3 225
350 7,3 225 7,2 225
400 8,1 265 8,0 265
400 8,1 265 8,1 260
400 8,1 265 8,1 270
400 8,1 510 8,1 440
:
4 N.m)
Etat
Epaisseur
(mm)
3,5 Point Ok
3,5 Point Ok
2,0 Point Ok
2,1 Point Ok
2,1 Point Ok
-
Point Ok
-
Point Ok
-
Point Ok
-
Point Ok
-
Point Ok
-
Pression faible
Unscrew the drain plug located under the
machine using a 10 mm torx spanner.
(Ref. S6262)
EN
59