Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
• Draw the master fingerprint over
the sensor again. The green LED
flashes appr. 3 secs, then the red
LED lights up.
• Draw the master fingerprint over
the sensor a third time. The green
LED flashes for appr. 3 secs, after
which the green LED lights up
continuously. The master fingerprint
has now been scanned in and is
valid. It is now possible to scan in
user fingerprints.
If a finger has been drawn over the
sensor and not recognized, the red
LED flashes for 3 seconds, after
which the green LED lights up.
Repeat the scanning-in process.
Scan in user fingerprints
Condition:
• Green LED is alight (operating
mode)
• Draw the master fingerprint once
over the sensor. The red LED lights
up.
• Draw the user fingerprint over the
sensor. The green LED flashes for
appr. 3 secs, then the red LED lights
up.
• Draw the user fingerprint over the
sensor again.
The green LED flashes for appr.
3 secs, then the red LED lights up.
• Draw the user fingerprint a third
time over the sensor. The green LED
flashes for appr. 3 secs, then stays
alight.
If a finger has been drawn over the
sensor and not recognized, the red
LED flashes for appr. 3 secs. The
green LED then lights up. Repeat the
scanning in process.
Check:
• Draw the user fingerprint once
over the sensor.
The green LED flashes and the relay
picks up.
Changing the operating
mode
In order to scan in the administrator
fingerprint and several master
fingerprints, you will first have to
change the operating mode. The
operating mode is set from the back
of the module.
7 Module removal
• Use the Vario key to unlock the
module (see also Siedle Vario
product information)
8 Setting the operating mode
• Open the flap on the back of the
module with the aid of a
screwdriver.
• Set the required operating mode
(0 to 9) at the rotary switch.
Once the required operating mode
has been set, close the flap and
replace the module.
Possible operating modes:
1 = Master mode
9 = Administrator mode
0, 2 - 8 = Delete mode
Administrator mode
Scan in the administrator
fingerprint
Condition:
• Administrator mode is set
The red LED lights (as-delivered
status)
The fingerprint you scan in first in
the administrator mode is the
administrator fingerprint.
• Draw the administrator fingerprint
over the sensor. The green LED
flashes for appr. 3 secs, then the
red LED lights up.
• Draw the administrator fingerprint
over the sensor again.The green LED
flashes for appr. 3 secs., after which
the red LED lights up.
• Draw the administrator fingerprint
a third time over the sensor. the
green LED flashes for appr. 3 secs,
after which the green LED lights up
continuously.
The administrator fingerprint has
now been scanned in and is valid.
Master fingerprints can now be
scanned in.
If a finger has been drawn over the
sensor and not recognized, the red
LED flashes for appr. 3 secs. The
green LED then lights up. Repeat the
scanning in process.
Scan in master fingerprints
• Draw the administrator fingerprint
over the sensor once. The red LED
lights up (scan-in mode for master
fingerprints).
• Draw the master fingerprint over
the sensor. The green LED flashes for
appr. 3 secs, then the red LED lights
up.
• Draw the master fingerprint over
the sensor again.The green LED
flashes for appr. 3 secs., after which
the red LED lights up.
• Draw the master fingerprint a third
time over the sensor.
The green LED flashes for appr. 3
secs, after which the green LED
lights up continuously.
The master fingerprint has now been
scanned in and is valid.
If you wish to scan in additional
master fingerprints (max. 5), repeat
the above described procedure.
Or if you now wish to go on to scan
in user fingerprints, jump to the
section "Scan in user
fingerprints".
If a finger has been drawn over the
sensor and not recognized, the red
LED flashes for appr. 3 secs. The
green LED then lights up. Repeat the
scanning in process.
Check:
• Draw the user fingerprint once
over the sensor. The green LED
flashes and the relay picks up.
7
Publicité
Table des Matières
