Master Mode - SSS Siedle FPM 611-0 Notice D'utilisation

Operating instructions/
Commissioning
The fingerprint module FPM 611-...
in the Vario design is an access
control system used in the "stand-
alone mode".
In this system, a scanned fingerprint
is used to actuate a function (such as
a door release). Up to 20 users
(scannable fingerprints) can be
managed by the system.
Which types of fingerprints
i i
exist and what can they do?
Any one finger can only be scanned
in for one fingerprint type
(administrator, master or user).
• Administrator fingerprint:
Issues entitlement to scan in max.
5 master fingerprints. Only one
administrator fingerprint can be
scanned in.
• Master fingerprint:
Issues entitlement to scan in max.
20 user fingerprints.
• User fingerprint:
Entitled to actuate the relay
integrated in the function (e.g. door
release). Only user fingerprints can
actuate this switching function.
For your own information, it is
advisable to note the fingerprints
and the people they belong to who
hold master and administrator
entitlement (see below).
Fingerprint table
Administrator fingerprint
Name
Finger/Hand
Master fingerprint 1
Name
Finger/Hand
Master fingerprint 2
Name
Finger/Hand
Master fingerprint 3
Name
Finger/Hand
etc..
6
4 Operating mode
i i
In the FPM 611-... there are two
different operating modes and a
delete mode available.
• Administrator mode;
One administrator fingerprint, up to
5 master fingerprints and up to 20
user fingerprints can be scanned in.

• Master mode;

One master fingerprint and 20
user fingerprints can be scanned in.
• Delete mode;
Deletes all fingerprints.
5 Module description
a Red LED
b Green LED
c LED for lighting
d Sensor
LEDs (a) and (b) signal the status.
• Red and green LEDs flash
alternately:
After power has been connected or
the device has been initialized.
• Red LED lights up:
Module is ready for scan-in of an
administrator, master or user
fingerprint.
• Green LED lights up:
(operating mode)
• Red and green LED off:
fingerprint recognition being
processed
• Green LED flashes for 3 secs, then
lights continuously:
Finger has been recognized.
• Red LED flashes for 2 secs, then
green LED lights continuously:
Finger has not been recognized,
repeat scan-in process.
• Red and green LED flash
simultaneously:
Initialization on switching on / delete
mode for all user fingerprints.
Important notes
!
• In individual cases, it can happen
that a fingerprint cannot be scanned
due to absence of biometric
characteristics.
This applies primarily to children and
older people. In these cases it is
possible that a fingerprint is not
recognized. In this case, try using a
different finger.
• Only one master fingerprint can
enable the authorization to read in
user fingerprints.
• If the rotary switch to set the
operating mode is adjusted, all
read-in fingers are deleted (as-
delivered status)!
6 Draw the finger correctly over
the sensor
• To ensure that the module is able
to reliably recognize your fingerprint,
draw it over the sensor to allow it to
be scanned in. Ensure that you
maintain as constant a speed,
position and light contact pressure
as possible.
• The read-in process must be star-
ted within 10 secs following activa-
tion, as otherwise the FPM 611-...
returns to the operating status.
• Interruptions longer than 15 secs.
automatically switch the system over
to the operating mode (time out).
Master mode
Scan in master fingerprint
The fingerprint module is in the
master mode in its as-delivered
status.
Conditions:
• Device is initialized
• Red LED is alight (as-delivered
status)
• Draw the master fingerprint over
the sensor. The green LED flashes for
appr. 3 secs. after which the red
LED lights up