Fronius TIG GRINDER MOBILE Instructions De Service page 3

BRIEF DESCRIPTION
7. How to Use :
● Make adjustments for the angle of the point (in degrees)
and the electrode diameter
- Loosen the central screw on the head
- Set the degree and the electrode
diameter by turning the head
- Tighten the central screw
The number of degrees equals the angle
of the point on the sharpened electrode:
● Guide the tungsten electrode through the opening that coincides with its
diameter;
● Turn on the TIG GRINDER MOBILE;
● Carefully press the tungsten electrode onto the revolving disc, while at the
same time rotating it with light pressure;
● Continue to rotate the electrode as it is removed from the disc until there is
no longer any contact;
● Inspect the results and, if necessary, repeat the process;
● The multi-functional cover with integrated opening slide makes it possible to
surface grind electrodes that have welding deposits due to the welding
process. In addition, ground electrodes can be optimised for aluminium
welding by being given a truncate cone.
● 3 steps adjustment for triple use of the grinding disc by turning the grinding in
position 1,2 or 3.
Warning ! Do not sharpen bent or burnt electrodes. Remove any drops on the point
of the electrode before it is sharpened. Use the electrode holder for short electrodes.
CHANGING THE GRINDING WHEEL
Remove the plug from the electrical socket before doing any maintenance on
this machine !
● Loosen the M 6 screws and remove them completely
● Remove head showing the angle adjustment
● Loosen the stud bolts on the sides
● Remove the house
● Loosen and unscrew the tension nut
● Change the wheel
● Warning ! Ensure that the wheel is mounted correctly
● Replace the washer
● Screw the nut back on and tighten it
USEFUL TIPS
The best results will be obtained by applying light pressure to the electrode while
at the same time rotating it on the disc. Remove the electrode before turning off
the grinder.
Using too much pressure while grinding will damage the grinder and require more
grinding discs; performance will suffer.
Warning : Always keep the air-intake vents clean.
Accessories : Only use FRONIUS accessories and spare parts.
Spare parts :
Grinding wheel
Grinding head 1.6 / 2.0 / 2.4 / 3.2
Grinding head 1.0 / 4.0 / 4.8 / 6.0
Multifunctional cover
Orbital set (option)
(Orbital set only with grinding head 1.0 / 4.0 / 4.8 / 6.0)
SYMBOLS
Read the instructions before
using this equipment.
Protect your eyes ! Wear safety goggles when using this equip-
ment.
Removal of used equipment, this tool can be disposed, free of
charge , at indicated local agencies.
This equipment has been tested according to
2014/30/EU, 2006/42/EC, 2011/65/EU
EN 60745-1:2009+A11:2010, EN 60745-2-23:2013, EN 50581:2012
Safety class II, safety insulation
x
Order No.
42,0411,0012
42,0510,0302
42,0510,0166
42,0411,0025
42,0510,0165
CHANGING THE WHEEL MOUNT
Remove the plug from the electrical socket before doing any maintenance on
this machine !
● Position spanner SW 13 on the spindle
● Position spanner SW 19 on the nut
● Loosen the nut
● Replace the wheel mount
● Tighten the nut
Follow the same
procedure to change
the spring collet, except
that the nut must be completely
unscrewed in order for the spring to be changed.
These procedures must be followed exactly as they are explained and illustrated.
Remove the plug from the electrical socket before doing any maintenance on
this machine !
The tension rod must have the same diameter
as the take-off shaft; otherwise the tension
rod will be damaged.
Fit the take-off shaft into
the tension rod.
The take-off shaft must rest
on the nut.
Very important !!!
Position spanner SW 13
on the spindle and tighten
the nut with SW 19.
Place the wheel on
the take-off shaft. Ensure
that it is properly mounted
and not crooked. Put on the
washer, screw on the nut and
tighten with spanner SW 10.
GENERAL SAFETY INSTRUCTIONS
PAY ATTENTION. Please observe these safety guideli-
nes. Not following them can cause electrical shock ,fire
and/or heavy injuiries.The following concept "electrical
tool" concerns tools with electrical flex as also tools
with build-in batteries.
PLEASE GUARD THESE INSTRUCTIONS CARE-
FULLY;
1. Working place.
a) Keep it tidy and clean. Disorder and low light can
occur accidents.
b) Don't use the tool in an dangerous explosive en-
vironment, where flammable products, gases and
dust are present. Electrical tools produce sparkles,
that can ignite the dust or gases.
c) Keep children and other persons away when using
an electrical tool.With an unexpected deviation one
can loose control on the tool.
2.Electrical safety.
a) The plug and socket must be appropriate. Don't
change the plug and don't use an adapter together
with an earthed tool. Unchanged plug and socket
decrease the risk of electrical shocks.
b) avoid body contact with earthed surfaces, such as
pipes,radiators,stoves and refrigerators. There is a
high risk of electrical shock if your body is earthed..
c) Protect the tool from rain and humidity. Water
penetration can cause electrical shock.
d) Don't use the flex as a handle to carry the tool, for
hanging it on the wall or to pull out the plug from
the socket. Keep the flex far from heat, oil, sharp
edges or revolving parts of equipment. Damaged
or twisted flexes increases the risk of electrical
shocks.
e) When working outside only use extension flexes
that has been approved for outdoor use. Doing so
one decreases the risk of electrical shock.
3. Safety of people.
a) Be attentive, look what you are doing, and be
ingenious when working with an electrical tool.
Don't use the tool when you are tired or under the
influence of drugs, alcohol or medicine. One short
moment of inattention can lead to severe injuries.
b) Always wear personal protection equipment, such
as safety goggles,anti slip shoes,safety helmet
or earmuffles,depending on the type of electrical
tools in use. Doing so reduces the risks of injuries.
c) Prevent the equipment from starting unexpectedly.
Make sure that the switch is on" off" before plug-
ging in. Never carry equipment that is connected
with your finger on the power switch.
- 3 -
Spindle + Nut
Wheel take-off shaft
Coated side
of wheel
Wheel
Washer
Nut
d) Check before starting that the key and adjustment
tools have been removed.
e) Don't overestimate yourself. Make sure to have a
secure posture and balance. Doing so ,you are in
better position to control the tool.
f) Wear the correct clothing. Don't wear loose clothing
or jewellery. Keep long hair ,clothes and gloves
away from revolving parts.
g) If mounting fume- and or dust- extractors make
sure that they are connected and used the right
way. Doing so is avoiding dust-problems.
4. Carefully handling and use of electrical tools.
a) Don't overload the tool. For every job use the
appropriate electrical tool. Doing so you will obtain
a better and safer result .
b) Don't use an electrical tool with a defect switch. A
tool with a defect switch can not be switched "off"
or "on", is dangerous and must be repaired.
c) Pull out the plug from the socket before you wish
to change the adjustments, change some parts
or putting away the tool. These measures prevent
unexpected start of the tool.
d) Keep unemployed electrical tools out of reach of
children Don't leave this tool in hands of people not
used to handle it or haven't not read these instruc-
tions. Electrical tools are dangerous when used by
inexperienced persons.
e) Take care of your tool. Please control if every tur-
ning part can work freely and isn't blocked, or that
some parts are broken or damaged. Let the tool
be repaired before use. Many accidents are due to
badly maintenance of electrical tools.
f) Keep cutting tools clean and sharp. Doing so one
gets a better grip and easier job done.
g) Only use electrical tools, spares aso,conform these
instructions for this tool .Take also into conside-
ration the environment and the job that has to be
done. The use of electrical tools for inadequate
jobs can lead to dangerous situations.
5. Service.
Have your tool serviced by qualified personal and
repaired only with original spare parts. Than you will be
sure that the safety of the tool is guaranteed.