Lubrication - RK Rose+Krieger DuoLine S Notice D'assemblage

7.4.1 Lubrication

3 Guide shaft lubrication
Oiled felt strips are
for lubricating (cleaning)
the guide shafts.
The felt strips must be re-oiled
periodically, according to the stressing,
via the shaft lubrication system.
Recommended lubricants:
Oil with viscosity of approximately 200
2
mm /s
at T = 40 °C e.g. SAE 90 transmission
oil.
First lubrication after approx. 2000
hours run.
Next interval:
every 1000 hours run,
Maintenance / re-greasing
Version
DuoLine 50x50
DuoLine 80x80
DuoLine 80 × 120
DuoLine 80 x 120-II
DuoLine 60
DuoLine 80
DuoLine 120
DuoLine 120 II
DuoLine 160
* Grease in two stages. After the first stage, drive the guide slides through three slide lengths and
then top up with the second stage.
Recommended lubricating interval taking the environmental factors and loading data specified in
these assembly instructions into consideration
** Grease in two stages. After the first stage, drive the guide slides through two slide lengths and
then top up with the second stage.
Recommended lubricating interval taking the environmental factors and loading data specified in
these assembly instructions into consideration
4 Section slide lubrication
The guide slides are lubricated directly
via the grease nipples.
Clean grease and oil from the
lubrication point before lubricating.
Ensure that the grease gun is axially
aligned with the flow direction of the
funnel-type lubricating nipple.
A high-pressure grease gun with a
needle extrusion tip must be used to
lubricate the RK DuoLine 50x50, 80x80
and 80x120(II) units.
A high pressure grease gun with an
extrusion tip must be used to lubricate
the RK DuoLine 80, 120 and 160 units.
Recommended lubricants:
Grease in accordance with DIN 51818
Viscosity class:
NLGI class 1
NLGI class 00
For use in max. range:
Grease in accordance with DIN 51818
Viscosity class NLGI class 2
Track rail guide*
(Lubrication every 1000 km)
3
2 x 0,4 cm
3
2 x 1.4 cm
3
2 x 1.4 cm
3
2 x 1.6 cm
3
2 x 0,8 cm
3
2 x 1.4 cm
3
2 x 2,8 cm
3
2 x 1,6 cm
3
2 x 2.8 cm
7. Life Phases 7. Life Phases 7. Life Phases
5 Spindle lubrication
Clean grease and oil from the
lubrication point before lubricating.
Ensure that the grease gun is axially
aligned with the flow direction of the
funnel-type lubricating nipple.
A high-pressure grease gun with a
needle extrusion tip must be used to
lubricate the RK DuoLine 50x50, 80x80
and 80x120(II) units.
A high pressure grease gun with an
extrusion tip must be used to lubricate
the RK DuoLine 80, 120 and 160 units.
Recommended lubricants:
Grease in accordance with DIN 51818
Viscosity class:
NLGI class 1
NLGI class 00
For use in max. range:
Grease in accordance with DIN 51818
Viscosity class NLGI class 2
Spindle**
(Lubrication every 300 km)
3
2 x 1 cm
3
2 x 2.5 cm
3
2 x 2.5 cm
3
2 x 2.5 cm
2 x 2 cm³
3
2 x 2.5 cm
-
-
3
2 x 5 cm
77 77 77