Cleaning; Troubleshooting; Disposal; Technical Data - Lux Tools E-SBS-21 Notice Originale

– Place the device with the edge of the foot plate (6)
on the work piece in such a way that the saw
blade does not touch the work piece.
– Turn on the device.
– Press the device firmly up against the work piece
and slowly plunge the blade into the work piece.
– As soon as the foot plate is positioned flat on the
work piece, continue sawing along the required
cutting line.
Tips for sawing
– When sawing, the foot plate must rest safety and
fully on the work piece.
– When sawing metal, apply coolant or lubrication
to the cutting line.
– When sawing small or thin work pieces always
use a stable surface or a work bench.
Things to note when sawing plastic
– When sawing plastic, if possible, use a new blade.
– When sawing, ensure speedy operation. If you
saw too slowly, the plastic will heat up, become
soft and adhere to the teeth of the blade. The cut
will be untidy and you will need to clean the blade.
Things to note when sawing metal
– When sawing metal, use a special blade.
– Saw with a low but even speed.
– When cutting profiles, start cutting at the thin side.
Error/Fault
Device does not work.
Sawing performance is not good
enough.
Saw blade distorted
If you can't fix the fault yourself, contact your nearest
vendor. Please be aware that any improper repairs
will also invalidate the warranty and additional costs
may be incurred.

Disposal

Disposal of the appliance
A crossed-out wheelie bin icon means: Bat-
teries and rechargeable batteries, electrical
or electronic devices must not be disposed of
with household waste. They may contain
substances that are harmful to the environ-
ment and human health.
Consumers must dispose of waste electrical devices,
spent portable batteries and rechargeable batteries
separately from household waste at an official collec-
tion point to ensure that these items are processed
correctly. Information on returning these items is
available from the seller. Sellers are required to
accept these items free of charge.
Batteries and rechargeable batteries, which
are not permanently installed in waste elec-
trical devices, must be removed prior to dis-
posal and must be disposed of separately.
Lithium batteries and battery packs in all systems
must only be retuned to a collection point when dis-
– When cutting U-shaped profiles, start cutting at

Cleaning

Cleaning overview
Regularly and according to the operating condi-
tions
What?
Clean the ventilation slots
of the motor to remove
dust.
Clean the device.

Troubleshooting

What to do when something doesn't work...
Malfunctions are often caused by minor faults. You
can easily remedy most of these yourself. Please
consult the following table before contacting the ven-
dor. You will save yourself a lot of trouble and possibly
money too.
Cause
Device is faulty?
Saw blade not suitable for the mate-
rial?
Saw blade is worn?
Too much load?
charged. Batteries must always be protected against
short circuits by covering the poles with adhesive
tape.
All end users are responsible for deleting any per-
sonal data stored on waste devices prior to their dis-
posal.
Disposal of the packaging
The packaging consists of cardboard and
correspondingly marked plastics that can
be recycled.
– Make these materials available for recy-

Technical data

Part number
Rated voltage
Capacity
Protection class
Protection type
Stroke rate at no load
Maximum cutting depth
• Wood
• Steel
the closed side.
DANGER! Risk of injury! Unprofessional
repairs may mean that your unit will no
longer operate safely. This endangers you
and your environment.
Remedy
Contact your local vendor.
Fit an appropriate saw blade.
► Fitting the saw blade – p. 26.
Reduce the pressure on the saw
blade.
cling.
GB
How?
Use a vacuum, cleaning
brush or paint brush.
Wipe the unit with a damp
cloth.
380459
230 V~, 50 Hz
900 W
II
IP20
-1
0–2800 min
115 mm
8 mm
27