Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Who may carry out maintenance and
servicing?
Operator
Work designated with the sign "Operator"
may only be carried out by persons who
have been instructed in the safe operation
and maintenance on the washing system.
Customer Service
Work designated with the sign "Customer
Service" may only be done by the fitters of
Kärcher Customer Service.
Maintenance contract
In order to guarantee a reliable operation
og the equipment, we success, you signed
a maintenance agreement. Please refer to
you local Kärcher service department.
Cleaning the wash hall
You can use the wash hall and tile cleaner
RM 841 ASF to clean the wash hall.
Manual operation
Your own safety and the safety of others
demands that the plant is switched off dur-
ing maintenance and service work. Howev-
er, not all plant parts on which maintenance
is being done are freely accessible. This
makes it necessary to move certain plant
parts during maintenance and servicing
work. The "manual mode" is intended to do
this. Manual operation is carried out using
the basic control panel.
Danger
Comply with the following sequence of
working steps for to ensure your own safety
and the safety of others.
Drive the vehicle out of the plant.
Ensure that no persons or animals are
in the plant.
Switch on plant.
Switch on manual operation.
Move plant parts.
Switch off plant and secure against it
switching on again.
Carry out maintenance and servicing
work.
Warning
Risk of damage to the plant and vehicle. Do
not use manual control for washing.
Activate manual operation
1 Automatic/manual switch
Turn automatic/manual switch to manu-
al position. STOP on the traffic light and
the "Reset" key on the control panel will
start blinking when manual mode is ac-
tive.
36
Manual mode basic control panel
Note
Not all manual functions can be executed
with the basic control panel. You need the
Adv. control panel to perform all manual
functions.
Select group
The manual functions are divided into
groups 1 through 7.
Press button or button combination
(press simultaneously) to obtain the de-
sired group.
1 Key "Reset"
2 Key "1"
3 Key "2"
4 Key "4"
Button
Group
1
1
Roof brush
X
2
Side brush
3
High pressure, in-
X
tensive
4
Portal
5
Water
X
6
Signals, card read-
er, traffic light
7
Frost protection (op-
X
tional)
The blinking sequence of the "Reset" key
and the position traffic light (option) show
the selected group.
Switch off group
Press the "Reset" key briefly.
Select function
Press button or button combination
(press simultaneously) to obtain the de-
sired function.
I: Function remains active as long as
–
the corresponding button is pressed.
0-I: function is activated the first time
–
the button is pressed and deactivated
when it is pressed again.
10
-
EN
Group 1, roof brush
Function
The roof brush rotates
forward
Roof brush rotates
backwards
Lower roof brush
Raise roof brush
Roof brush/roof bar -
fast drive
Group 2, side brushes
Function
Rotate side-brushes for-
wards
Rotate side-brushes
backwards
Move in side-brush 1
Move out side-brush 1
Move in side-brush 2
Move out side-brush 2
Inching mode, side
brushes
Group 3, high pressure, in-
tensive
Function
High pressure roof
High-pressure side
Lower the roof bar
Raise the roof bar
Swivel the roof bar, front 0-I X
Swivel the roof bar, rear 0-I
Intensive, side
2
4
Group 4, portal
Function
X
Portal forwards
X
Portal backwards
X
Portal fast drive
X
(Initialise machine)
X
X
Group 5, water
Function
X
X
Dosing pump CTH, front
bow (A)
Dosing pump CTH, rear
bow (C)
Foam (B)
Brush irrigation of proc-
essed water A+B+(C)
Brush irrigation fresh
water A+B
Post rinse bow fresh
water C
Dosing pump shampoo 0-I X
Button
1
2
4
0-I X
0-I
X
I
X
X
I
X
I
X
X
Button
1
2
4
0-I X
0-I
X
I
X
X
I
X
I
X
X
I
X
X
I
X
X
X
Button
1
2
4
0-I X
0-I
X
I
X
X
I
X
X
X
X
0-I X
X
X
Button
1
2
4
I
X
I
X
0-I X
X
I
X
Button
1
2
4
0-I X
0-I
X
0-I X
X
0-I
X
0-I X
X
0-I
X
X
X
X
Publicité
Chapitres
Table des Matières
Dépannage
