Standard Parameters - Danfoss VACON 100 FLOW Instructions D'installation

2.6 S
PECIFIC PARAMETERS TO THE OPERATING MODE WITH DIFFERENTIAL PRESSURE SENSOR
2.6.1

Standard parameters

N° par. Désignation
P 3.9.2.1 Motor
Thermal
Protection
P 3.2.4 Start
Function
P 3.3.1.5 I/O Control
Reference
A Selection
P 3.5.2.1.2 AI1 Signal
Filter Time
P 3.5.1.2 Control
Signal 2 A (s)
P 3.5.1.12 External
Fault Open
P 3.5.1.21 Preset
Frequency
Selection 0
P 3.5.3.2.1 RO1
Function
P 3.5.3.2.4 RO2
Function
P 3.1.2.6 Motor
Switch
P 3.1.2.3 Switching
Frequency
(kHz)
P 3.9.1.4 Undervoltag
e Fault
P 5.8.1.1 Protocole
P 5.8.3.1.1 Adresse
esclave
P 5.8.3.1.2 Débit en
bauds (bps)
P 5.8.3.1.3 Type de
parité
P 5.8.3.1.4 Bits d'arrêt
P 5.8.3.1.5 Tempo. com.
(s)
P 5.6.1.1 Fan Control
Mode
Valeur Min
0 = No 0 = No
action action
1 = Flying Ramping
start
7 = PID 0 = PC
1 0
DigIN N/A
Slot0.1
DigIN N/A
SlotA.2
DigIN N/A
SlotA.3
3 = No used
General
fault
2 = Run No used
1 = 0 =
Enabled Disabled
10 1,5
1 = Fault 0 = Fault
not stored in
stored in history
4 = Aucun
ModBus protocole
RTU
12 1
9600 = 300
9600
3 = Aucun Pair
1 = 1 1
5 0
1 = 0 =
Optimise Always on
d
Page 31
Max Default
3 = Fault 2 = Fault
(Stop by (Stop by
stop
mode)
Flying start Ramping
20 = Block AI1+AI2
Out.10
300 0,1
N/A DigIN
SlotA.2
N/A DigIN
Slot0.2
N/A DigIN
SlotA.4
AHF Cap Run
Disconnect
Inv
AHF Cap Défault
Disconnect
Inv
1 = Enabled 0 =
Disabled
10 0
1 = Fault 0 = Fault
not stored stored in
in history history
15 Aucun
protocole
247 1
230400 9600
Aucun Aucun
2 2
65535 10
1 = 0 =
Optimised Always on
ID Observations
704 converter response in the
event of
overtemperature fault.
505 Start Function
117 source of the frequency
reference when the control
source is I / O A.
378 filter the disturbances of the
analog input signal.
404 logic input signal (control
signal 2) which controls the
start and stop of the
converter when the control
source is I / O A (AR).
406 logic input signal that
activates an external fault.
419 logic input signal for
selecting the preset
frequencies.
11001 function or signal connected
to the relay output.
11004 function or signal connected
to the relay output.
653 activation of the function
Interrupt mot.
601 frequency of switching of the
frequency converter.
727 Undervoltage faults must or
may not be recorded in the
fault history.
2208 Protocole
2320 Adresse esclave
2378 Débit en bauds
2379 Type de parité
2380 Bits d'arrêt
2321 Tempo. communic.
2377 Fan Control Mode
motor
Dec 2017