Service & Maintenance; Propeller Replacement; General Maintenance - MINN KOTA Fortrex 112 Manuel De L'utilisateur

SERVICE & MAINTENANCE

PROPELLER REPLACEMENT

TOOLS AND RESOURCES REQUIRED:
• Box End Wrench
- 1/2" for motors with 70 lbs thrust or lower.
- 9/16" for motors with 80 lbs thrust or higher.
• Screwdriver (optional)
CAUTION:
Disconnect the motor from the battery
before beginning any prop work or
maintenance.
NOTE: The propeller on your motor may diff er from
the one pictured.
1. Disconnect the motor from all sources of power prior to changing the propeller.
2. Hold the propeller and loosen the prop nut with pliers or a wrench.
3. Remove the prop nut and washer. If the drive pin is sheared or broken, you will need to hold the shaft stationary with a blade
screwdriver pressed into the slot on the end of the shaft.
4. Turn the old prop to horizontal (as illustrated) and pull it straight off . If drive pin falls out, push it back in.
5. Align the new propeller with the drive pin.
6. Install the prop washer and prop nut.
7. Tighten the prop nut 1/4 turn past snug [25-35 inch lbs.] Do not over tighten as this can damage the prop.

GENERAL MAINTENANCE

• After use, the entire motor should be rinsed with freshwater. This series of motors is not equipped for saltwater exposure.
GENERAL MAINTENANCE
• The composite shaft requires periodic cleaning and lubrication for proper retraction and deployment. A coating of an aqueous
based silicone spray will improve operation.
• After use, the entire motor should be rinsed with freshwater. This series of motors is not equipped for saltwater exposure.
• The composite shaft requires periodic cleaning and lubrication for proper retraction and deployment. A coating of an aqueous • The propeller must be inspected and cleaned from weeds and fi shing line after every use.
based silicone spray will improve operation. Fishing line and weeds can get behind the prop, damage the seals and allow water to enter the motor.
• Verify the prop nut is secure each time the motor is used.
• The propeller must be inspected and cleaned from weeds and fi shing line after every use.
Fishing line and weeds can get behind the prop, damage the seals and allow water to enter the motor.
• To prevent accidental damage during transportation or storage, disconnect the battery whenever the motor is off of the water.
For prolonged storage, lightly coat all metal parts with an aqueous based silicone spray.
• Verify the prop nut is secure each time the motor is used.
• For maximum battery life recharge the battery(s) as soon as possible after use. For maximum motor performance restore
• To prevent accidental damage during transportation or storage, disconnect the battery whenever the motor is off of the water.
For prolonged storage, lightly coat all metal parts with an aqueous based silicone spray. battery to full charge prior to use.
• Keep battery terminals clean with fi ne sandpaper or emery cloth.
• For maximum battery life recharge the battery(s) as soon as possible after use. For maximum motor performance restore
battery to full charge prior to use.
• The propeller is designed to provide weed free operation with very high effi ciency. To maintain this top performance, the
• Keep battery terminals clean with fi ne sandpaper or emery cloth. leading edge of the blades must be kept smooth. If they are rough or nicked from use, restore to smooth by sanding with fi ne
sandpaper.
• The propeller is designed to provide weed free operation with very high effi ciency. To maintain this top performance, the
• The rail covers on the motor rest are intended to be a wear item and may need to be a replaced periodically. leading edge of the blades must be kept smooth. If they are rough or nicked from use, restore to smooth by sanding with fi ne
sandpaper.
• The rail covers on the motor rest are intended to be a wear item and may need to be a replaced periodically.
16 | minnkotamotors.com
Propeller
Prop Nut
Washer
Slot End
Drive Pin
©2017 Johnson Outdoors Marine Electronics, Inc.