Gaspardo PENTA PE Emploi Et Entretien page 27

the seeder transfers onto the three-point linkage. If in doubt
consult the tractor Manufacturer.
28)Comply with the maximum admissible weight for the axle,
the total mobile weight, transport regulations and the highway
code.
Transport on Road
29)When driving on public roads, be sure to follow the highway
code of the country involved.
30)Any transport accessories must be provided with suitable
signs and guards.
31)It is very important to remember that road holding capacity as
well as direction and braking capacity can be influenced,
sometimes con-siderably, by equipment being either carried
or towed.
32)When negotiating curves, be aware of the variation in
centrifugal force exerted in a position other than that of the
center of gravity, with and without the equipment in tow. Also
pay greater attention on sloping roads or ground.
33)For transport, adjust and fasten the lateral lifting arm chains
of the tractor; check that the seed and fertilizer hopper covers
are closed properly; lock the hydraulic lifting control lever.
34)Road movements must be performed with all tanks empty.
35)For displacements beyond the work area, the equipment must
be placed in the transportation position.
36)Upon request the Manufacturer will supply supports and
tables for signaling of dimensions.
37)When the dimensions of carried or partially-carried equipment
conceal the tractor's signalling and lighting devices, these
must also be installed on the equipment itself, in conformity
with regulations of the highway code of the country involved.
When in operation make sure that the lighting system is in
perfect working order. It is also important to remember that
the correct signalling sequence of the headlights includes
(Fig. 5):
A - Direction indicator;
B - Red position light;
C - Stop light
Cardan shaft
38)The equipment installed can only be controlled by means of
the Cardan shaft complete with the necessary overload safety
devices and guards fastened with the appropriate chain.
39)Only the Cardan shaft supplied by the Manufacturer must be
used.
40)The engine must not be running when installing and removing
the Cardan shaft.
41)Care must be taken regarding the safety and correct assembly
of the Cardan shaft.
fig. 6
cod. 19501162
USE AND MAINTENANCE
42)Use the chain provided to stop the Cardan shaft from rotating.
43)Always check carefully that the Cardan shaft guard is always
in position, both during trans-portation and operation.
47)Frequently and set intervals check the Cardan shaft guard, it
must always be in excellent condition.
45)Before engaging the power take-off, check that the set rpm
corresponds to that indicated by the sticker on the equipment.
46)Before inserting the power take-off, make sure that there are
no people or animals nearby and that the rpm selected
corresponds to that permitted. Never exceed the maximum
admissible speed.
47)Watch out for the rotating universal joint.
48)Do not insert the power take-off with the engine off or
synchronized with the wheels.
49)Always disconnect the power take-off when the Cardan shaft
is at too wide an angle (never more than 10° - Fig. 6) and
when it is not being used.
50)Only clean and grease the Cardan shaft when the power take-
off is disconnected, the engine is off, the hand brake pulled
and the key removed.
51)When not in use, place the Cardan shaft on the support
provided for it.
52)After having dismantled the Cardan shaft, place the protective
cover on the power take-off shaft again.
Maintenance in safety
53)Do not proceed with maintenance and cleaning if the power
take-off has not been disconnected first, the engine power
off, the hand brake pulled and the tractor blocked with a wooden
block or stone of the right size under the wheels.
54)Periodically check that the bolts and nuts are tight, and if
necessary tighten them again. For this it would be advisable
to use a torque wrench, respecting the values of 53 Nm for
M10 bolts, resistance class 8.8, and 150 Nm for M14 bolts
resistance class 8.8 (Table 1).
55)During assembling, main-tenance, cleaning, fitting, etc., with
the seeding machine raised, place adequate supports under
the equipment as a precaution.
56)The spare parts must correspond to the manufacturer's
specifications. Use only original spares.
g
ENGLISH
Table 1
27