Advance Advenger 2800ST Mode D'emploi page 16

A-16 / ENGLISH
DETERGENT SYSTEM PREPARATION AND USE (REV ECOFLEX)
COMMON INSTRUCTIONS:
The Detergent Cartridge (13) is located behind the Detergent Cartridge Access Door (12) in the operator's compartment. Fill the detergent cartridge with a
maximum of 1.25 gallons (4.73 Liters) of detergent. SERVICE NOTE: Remove the detergent cartridge from the detergent box prior to fi lling to avoid spilling
detergent on the machine.
It is recommended that a separate cartridge be used for each detergent you plan to use. The detergent cartridges have a white decal on them so you can write the
detergent name on each cartridge to avoid mixing them up. When installing a new cartridge, remove the Cap (AA) and place the cartridge in the detergent box.
Install the Dry Break Cap (BB) and detergent hose as shown.
The system should be purged of previous detergent when switching to a different detergent. SERVICE NOTE: Move machine over fl oor drain before purging
because a small amount of detergent will be dispensed in the process.
To Purge When Changing Detergent:
1 Disconnect and remove the detergent cartridge.
2 Turn the Key Switch (A) ON. Press and hold the Solution ON / Increase Switch (B) and the Detergent ON/OFF Switch (E) down for 3 seconds. NOTE: Once
activated the purge process takes 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to purge
the system.
To Purge Weekly:
1 Disconnect and remove the detergent cartridge. Install and connect a Cartridge fi lled with clean water.
2 Turn the Key Switch (A) ON. Press and hold the Solution ON / Increase Switch (B) and the Detergent ON/OFF Switch (E) down for 3 seconds. NOTE:
Once activated the purge process takes 10 seconds. See illustration on next page for Detergent System indicators. Normally one purge cycle is adequate to
purge the system.
When the Detergent Cartridge (13) is almost empty a Display Panel (F4) indicator will come on. The "Low Detergent" indicator will remain on until you reset the
system. Once this indicator comes on you should be able to simply pour an entire gallon bottle of detergent into the Cartridge to refi ll without worrying about
measuring. NOTE: Only reset the system when the cartridge is full. When switching cartridges, the "Low Detergent" indicator is only accurate if the replacement
cartridge is at the same level as the cartridge being replaced.
To Reset:
1 Turn the Key Switch (A) ON. Press and hold the Solution ON / Increase Switch (B) and the Solution Decrease / OFF Switch (D) down for 3 seconds. See
illustration on next page for Detergent System indicators.
Detergent Ratio (SCRUB AND SOLUTION SYSTEM MUST BE ON):
No detergent is dispensed until the scrub and detergent systems are activated and the Drive Pedal (3) is pushed forward.

The Detergent Ratio Indicator
There are 4 modes of EcoFlex operation:
1. Chemical Free Cleaning Mode – During scrubbing, the detergent system can be turned off at any time to allow scrubbing with water only.
Press the Detergent Switch (E) until the Detergent Indicator is OFF and Detergent Indicator Bar Graph (F10) displays both left and right
boxes empty.
2. Weak Detergent Mode – Detergent Indicator ON, Detergent Indicator Bar Graph (F10) displays left box fi lled and right box empty. Pressing the
Detergent Switch (E) will cycle from weak to strong to OFF and back to weak in a repeating sequence. See below the steps "To program the
Weak Detergent Ratio".
3. Strong Detergent Mode – Detergent Indicator ON, Detergent Indicator Bar Graph (F10) displays both left and right boxes fi lled. Pressing the
Detergent Switch (E) will cycle from weak to strong to OFF and back to weak in a repeating sequence. See below the steps "To program the
Strong Detergent Ratio". Do not use a detergent level exceeding the detergent manufacturer's recommendation.
4. Burst of Power – Press the Burst of Power Switch (J) to temporarily (1 minute) engage the strong detergent strength and increase both the
solution fl ow rate and brush pressure to the next available level. The Burst of Power Indicator will blink during this 1 minute interval, after
which all scrub parameters will return to their previous state.
To program the Strong Detergent Ratio (Always program the strong detergent strength fi rst and then the weak)
1. Press the OneTouch™ Scrub Switch
2. Press the Detergent Switch
3. Press and hold the Detergent Switch
mode the right box of (F10) will fl ash. Also the detergent ratio (F5) and indicator will begin to fl ash.
4. While the indicators are fl ashing, pressing and releasing the Detergent Switch
percentage are displayed together.
Ratio = 1:32, 1:50, 1:64, 1:100, 1:128, 1:150, 1:200, 1:256, 1:300.
5. Once the desired ratio is displayed on the screen
6. If the weak setting is currently set to a higher value than the new strong programmed setting, the software will automatically adjust the weak setting to
be one value weaker than the strong setting.
To program the Weak Detergent Ratio/Percentage
1. Press the OneTouch™ Scrub Switch
2. Press the Detergent Switch
3. Press and hold the Detergent Switch
mode the left box of (F10) will fl ash. Also the detergent ratio (F5) and indicator will begin to fl ash.
4. While the indicators are fl ashing, pressing and releasing the Detergent Switch
value weaker than or equal to the strong setting, so only the values that fall within that range will be displayed as you cycle through them.
5. Once the desired ratio is displayed on the screen
A-16 - FORM NO. 56041735 - Advenger
(F5) will always be displayed when the detergent system is on.
(H) to activate the scrub system.
(E) until the Bar Graph (F10) displays Strong detergent (both left and right boxes fi lled).
(E) again for 3 seconds to enter the programming mode. Once you have entered the strong detergent adjustment
(F5), stop and it will save the setting after 3 seconds.
(H) to activate the scrub system.
(E) until the Bar Graph (F10) displays Weak detergent (left box fi lled and right box empty).
(E) again for 3 seconds to enter the programming mode. Once you have entered the weak detergent adjustment
(F5), stop and it will save the setting after 3 seconds.
™
(E) will cycle through the options. The ratio and it's corresponding
(E) will cycle through the available options. The weak setting must be a
revised 2/13