Maintenance And Repair - Parkside PKS 1500 A1 Consignes D'utilisation Et De Sécurité

Connect a dust collecting device to the electric tool
–
when sawing wood. The emission of dust is influ-
enced, among other things, by the type of material
to be processed, the significance of local separation
(collection or source) and the correct setting of the
hood/guide plates/guides.
Do not use saw blades made of high-speed alloy
–
steel (HSS steel).

Maintenance and repair

2
Pull out the mains plug for any adjustment or repair
–
tasks.
– The generation of noise is influenced by various
factors, including the characteristics of saw blades,
condition of saw blade and electric tool. Use saw
blades which were designed for reduced noise de-
velopment, insofar as possible. Maintain the electric
tool and tool attachments regularly and if necessary,
initiate repairs in order to reduce noise.
Report faults on the electric tool, protective devices
–
or the tool attachment to the person responsible for
safety as soon as they are discovered.
Safe work
3
– Only use saw blades for which the maximum permis-
sible speed is not lower than the maximum spindle
speed of table saws and which are suitable for the
material to be cut.
Make sure that the saw blade does not touch the
–
rotary table in any position by pulling out the mains
plug and rotating the saw blade by hand in the 45°
and 90° position. If necessary, readjust the saw
head.
When transporting the electric tool, only use the
–
transport devices. Never use the protective devices
for handling or transport.
Make sure that the lower part of the saw blade
–
is covered during transport, e.g. by the protective
device.
Be sure to only use spacers and spindle rings speci-
–
fied by the manufacturer as suitable for the intended
purpose.
The floor around the machine must be level, clean
–
and free of loose particles, such as chips and cutting
residues.
– Do not remove any cutting residues or other parts of
workpieces from the cutting zone while the machine
is running and the saw unit is not at rest.
Make sure that the machine is always secured on a
–
workbench or a table if at all possible.
Support long workpieces (e.g. with a roller table) to
–
prevent them sagging at the end of a cut.
Warning! This electric tool generates an electromagnetic
field during operation. This field can impair active or passive
medical implants under certain conditions. In order to prevent
the risk of serious or deadly injuries, we recommend that per-
sons with medical implants consult with their physician and
the manufacturer of the medical implant prior to operating
the electric tool.
16 GB/IE
SAFETY INSTRUCTIONS FOR THE HANDLING
OF SAW BLADES
1
Only use insertion tools if you have mastered their use.
2 Observe the maximum speed. The maximum speed
specified on the insertion tool may not be exceeded. If
specified, observe the speed range.
3
Observe the motor / saw blade direction of rotation.
4
Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
5 Clean grease, oil and water off of the clamping sur-
faces.
6
Do not use any loose reducing rings or bushes for the
reducing of holes on saw blades.
7
Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have at least
1/3 of the cutting diameter.
8 Make sure that fixed reducer rings are parallel to each
other.
9
Handle insertion tool with caution. They are ideally
stored in the originally package or special containers.
Wear protective gloves in order to improve grip and to
further reduce the risk of injury.
10
Prior to the use of insertion tools, make sure that all
protective devices are properly fastened.
11
Prior to use, make sure that the insertion tool meets
the technical requirements of this electric tool and is
properly fastened.
12
Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from
accidents using suitable precautionary
measures!
• Do not look directly into the laser beam with unprotected
eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces
and persons or animals. Even a laser beam with a low
output can cause damage to the eyes.
• Caution - methods other than those specified here can
result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure to
the beam can occur.
• If the mitre saw is not used for an extended period of
time, the batteries should be removed.
• The laser may not be replaced with a different type of
laser.
• Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.