Troubleshooting Procedures; Optional Bluewave® Spa Stereo System - Jacuzzi J-300 Série Manuel D'installation Et Utilisation Et Entretien

Note: As a safety measure, the red lights of the spa will flash on and
off as an indication that the spa is an overheat condition.
To correct condition:
Remove the spa's cover and allow your spa to cool down.
Program the heater settings for Economy Mode. Raise water
temperature setting to cancel Summer Logic condition.
If the condition persists, contact your authorized Jacuzzi dealer.
Panel Displays (-- -- -- --)
WARNING: Risk of Hyperthermia (over-heating) Causing Se-
vere Injury, burns, or welts.
Water temperature is above acceptable limits. DO NOT ENTER
SPA! The safety "Watchdog" software has been triggered and the
spa is deactivated. A problem has been detected which could
cause damage to the spa or its components. The display will
alternate between "-- -- -- --" and the scrolling message "WA-
TCHDOG CALL FOR SERVICE" as long as the error exists. Contact
your authorized Jacuzzi dealer or qualified service technician.
Note: As a safety measure, the red lights of the spa will flash on
and off as an indication that the spa is in watchdog condition.

Troubleshooting Procedures

In the event your Jacuzzi spa is not working the way it should, plea-
se first review all the installation and operating instructions in this
manual and check for messages on the panel display. If you are still
not satisfied it is working properly, please follow the appropriate
troubleshooting instructions below.
Always insist on genuine Jacuzzi replacement parts.
Note: If any of the supply cords to accessories are damaged,
they must be replaced by authorized service personnel. Contact
your authorized Jacuzzi dealer or qualified service technician.
FL--1 and FL--2
To try an correct an FL--1 and FL--2 condition perform the fol-
lowing:
1. Verify water level is above all jets but below lowest pillow.
Add water if necessary.
2. Check for clogged or dirty filter cartridge (Sec. "Cleaning The
Filters").
3. Purge "air lock" from circulation pump intake by removing
filter cartridge. Hold your garden hose over the filter cartridge
wall fitting while using a rag as a seal around hose end. Ask a
helper to turn on water for 30 seconds, then turn off. Reinstall
filter cartridge and check spa (Sec. "Cleaning The Filters").
4. If the circulation pump is not running, turn power off at the
main breaker, then turn power back on. This will reset the circu-
lation pump priming cycle. Once the pump is primed, the error
should clear.
5. If problem persists, contact your authorized Jacuzzi dealer.
None of the Components Operate (e.g. Pump, Light)
Check the following:
1. Is there power to the spa?
2. Is the household circuit breaker tripped?
3. Contact your authorized Jacuzzi dealer or qualified service
technician.
Pump Does Not Operate
Press the JETS 1 button. If no water movement is detected, make
sure power is going to the spa and check the water level. If this
does not solve the problem, contact your authorized Jacuzzi de-
aler or qualified service technician. The main jets pump 1 opera-
tes but no water flows to jets. Check the following:
1. Jets may all be closed. Verify all jets are in the open "on" po-
sition.
2. Pump may not be properly primed. This can happen after the
spa is drained and refilled. Press the JETS 1 button on the control
panel several times, never leaving the motor running for more
than 5 to 10 seconds at a time. Turn power off and let the air out
of spa plumbing system by removing the filter cartridge (Sec.
"Cleaning The Filters"). Make certain you reinstall the filter cartri-
dge before turning on spa power and restarting the jets pump 1.
Poor Jet Action
Make sure all jets are in the full open "on" position.
Press the JETS 1 button to make certain pump #1 is on.
Verify all air controls are in the "on" position by pressing down on
their Jacuzzi Logo (Sec. "Air Controls").
Check for dirty filter. Clean, if necessary.
Water is Too Hot
Reduce thermostat setting.
No Heat
1. Check thermostat setting.
2. Keep the spa cover in place while heating.
3. Check the settings to see if your spa is in economy mode (Sec.
"Programming the Heating Mode").
Should checking the above steps fail to correct the problem,
please call your Jacuzzi Hot Tub dealer so that they may arrange
service.
Optional BLUEWAVE® Spa Stereo System
To start enjoying your new stereo receiver, please read the following
operation instructions in their entirety.
1
38
2
USB
AUX
3 4
5
6
7