Devices Addition Or Removal; Stop Input - Nice MhouseKit WG2W Instructions Et Avertissements Pour L'installation Et L'utilisation

the row with the value of Ed and the column with the value of K. The
box contains the maximum possible number of cycles per day (e.g.
Ed= 2800 and K= 105; daily cycles ≈ 22).
If the number obtained is too low for the intended use, or falls within the
"not recommended usage area", you can evaluate the use of 2 or more
solar power panels or a solar power panel of greater power. Contact the
Nice Support Service for further information.
The method described, allows you to calculate the maximum possible
number of cycles per day that the automation is capable of carrying out,
according to the solar energy supplied. The calculated value should be
considered as the average value and equal for all the days of the week.
Considering the presence of the accumulator, which acts as an energy
"store", and considering that the accumulator allows you independent
Ed K≤75 K=100
9500
123
9000
116
8500 109
8000 103
7500 96
7000 89
6500 83
6000 76
5500 69
5000 63
4500 56
4000 49
3500
43
3000
36
2500
29
2000 23 17
1500 16 12
1000 9
K≤75 K=100
741 556

10.3 - DEVICES ADDITION OR REMOVAL

Devices can be added to or removed from an automation which is auto-
mated with WG2W at any time.
Caution! – Do not add devices before you have checked that they
are fully compatible with WG2W; for details please contact the
Nice Support Service.

10.3.1 - STOP input

STOP is the input that stops movement immediately, (with a brief reverse
of the manoeuvre). Devices with output featuring normally open "NO"
contacts and devices (for instance, the KS100 selector switch), and with
normally closed "NC" contacts, as well as devices with 8.2kΩ constant
resistance output, like sensitive edges, can be connected to this input.
Multiple devices, even of different types, can be connected to the STOP
input if suitable arrangements are made; see Table 13.
NO
NO In parallel (note 2)
NC (note 1)
8.2 kΩ In parallel
Note 1. NO and NC combinations are possible by placing the 2 contacts
in parallel, taking care to place a 8.2 k Ω resistance in parallel to the NC
contact (thus enabling the combination of 3 devices: NO, NC and 8.2k Ω ).
Note 2. Any number of NO devices can be connected to each other in
parallel.
Note 3. Any number of NC devices can be connected to each other in
series.
Note 4. Only two devices with 8.2k Ω constant resistance output can be
connected in parallel; if needed, multiple devices must be connected "in
cascade" with a single 8.2 k Ω terminal resistance.
Caution! – If the STOP input is used to connect devices with safety
functions, only the devices with 8.2 kΩ constant resistance output
guarantee the failsafe category 3.
22 – English
TABLE A - Maximum number of cycles per day
K=125 K=150
92 74 61
87 70 58
82 66 55
77 62 51
72 58 48
67 54 45
62 50 41
57 46 38
52 42 35
47 38 31
42 34 28
37 30 25
32 26 21
27 22 18
22 18 15
14 11
10 8
7 6
TABLE B - Maximum number of cycles just on accumulator charge
K=125 K=150 K=175
445 371 318
TABLE 13
1st device type:
NC 8.2 kΩ
(note 1) In parallel
In series (note 3) In series
In series (note 4)
automation even during long periods of bad weather (when the solar
panel produces very little energy) it is therefore possible to occasionally
exceed the maximum number of cycles per day, provided that the aver-
age on 10-15dd is within the limits.
In table B below the maximum possible number of cycles is shown,
according to theseverity index (K) of the manoeuvre, using the stored
solar energy of the accumulator. It is assumed that initially the accumula-
tor is fully charged (e.g., after a long period of good weather or after a refill
with the optional power supply model PCB) and that the operations are
carried out within a period of 30 days.
When the accumulator has exhausted its energy, the led will start to report
on the discharged status of the battery with a short flash every 5 seconds,
accompanied by a "beep" sound.
K=175 K=200 K=225
53 46 41
50 44 39
47 41 36
44 39 34
41 36 32
38 34 30
35 31 28
33 29 25
30 26 23
27 24 21
24 21 19
21 19 16
18 16 14
15 14 12
13 11 10
10 9 8
7 6 5
K=200 K=225
278 247
The control unit recognises the type of device connected to the STOP
input during the self-learning phase; after which a STOP command is acti-
vated whenever a variation with respect to the learned status is detected.
10.3.2 - Recognition of other devices connected to the STOP input
Normally the recognition of the Power&Free System devices connected
to the STOP input takes place during the installation stage. However, if
new devices are added to or old ones removed from the STOP input, the
recognition process can be repeated for these devices only by proceed-
ing in the following way:
01. On the control unit, press and hold P3 (fig. 38), for at least three
seconds, then release it.
02. Wait a few seconds until the control unit has completed the device
recognition procedure.
03. When the recognition procedure has completed, the P3 LED (fig. 38)
will go off. If the P3 LED flashes, it means that an error has occurred;
see section 10.5 "Troubleshooting".
04. After you have added or removed any devices, the automation sys-
tem must be tested again according to the directions contained in
paragraph 8.1 "Testing".
10.3.3 - Adding further wireless devices to an existing system
This procedure allows you to add more wireless devices to an existing
wireless network, without the need to recapture the devices already
installed.
01. Warning – The new wireless scanning devices should not have been
used on other systems; otherwise, you need to restore to factory set-
tings using the steps outlined in paragraph 10.3.6.
02. Press and hold P1 (fig. 38) of the control unit and release it after the
green Led illuminates. Now the Led will flash quickly and the control
unit will try to communicate with each of the devices that are already
installed in the system (on the wireless devices the Led "A" will flash
with green light and the Led "B" will flash- fig. 39). On completion, the
control unit Led will illuminate with solid green light, placing the control
unit into "radio listen" mode for the acquisition of new devices.
Caution! – If the device does not communicate, the control unit will
emit a sound (beep) for 10 seconds. If you do not press any other
button, at the end of 10 seconds the control unit stops the capturing
phase, keeping the system in the previous state.
K=250 K=275 K=300
37 33 31
35 32 29
33 30 27
31 28 26
29 26 24
27 24 22
25 23 21
23 21 19
21 19 17
19 17 16
17 15 14
15 13 12
13 12 11
11 10 9
9 8 7
7 6 6
Usage not recommended area
K=250 K=275 K=300
222 202 185
K≥325
28
27
25
24
22
21
19
18
16
14
13
11
10
8
7
5
K≥325
171