Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
4. Using your Accu Hand Lawnmower correctly
The Brill Accu Hand Lawnmower
380 ASM is designed for cut-
ting lawns in and around the
garden. It is not designed for
use in public facilities, parks,
sporting grounds, on roads,
in agriculture or forestry.
It is essential to observe the
manufacturer's operating instruc-
tions to ensure the unit's proper
functioning.
5. Assembling the Accu Hand Lawnmower
5.1. Checking all parts are
included
The Accu Hand Lawnmower
box contains the following
parts:
Accu Hand Lawnmower
1 PowerAccu 24 PA
1 upper section of the
guide handle
1 middle section of the
guide handle
1 lower section of the
guide handle
Assembly parts for the guide
handle in a plastic bag
1 Charger LG 24 (24 Volt)
1 thickness gauge
Operating instructions
5.2. Assembling the guide
handle
(Fig. A – M)
1. Tilt your Hand Lawnmower
so that the black rollers face
upwards (Fig. B/C).
Fit the lower section of the
guide handle (5) so that the
drilled holes (10) are over
handle bolts (11) (Fig. B).
Note: Make sure that the
groove in the drilled hole (10)
and the locking tab of the
handle bolt (11) meet (Fig. D).
Warning! Do not use exces-
sive force. First ensure that
the recess in the handle
and the lug of the bolt are
The operating instructions
also contain advice for service,
maintenance and repair.
Attention ! To prevent injury,
A
the Accu Hand Lawnmower
must not be used for trimming
bushes, hedges, shrubs, for cut-
ting and pruning of climbers
or grass on roofs or in balcony
boxes.
in alignment and then fix
together.
2. Continue assembling the
guide handle as follows using
the black central connecting
section:
Disassemble the central
connecting section (27)
(referred to as the "node"
from now on).
The front and rear sides of the
node are fastened together by
a clip lock to prevent them
from springing open. The
clip lock can be found in the
recess on the back of the
node. For easier disassembly,
release the clip lock by
pushing it outwards.
Press the four nuts into the
recesses in the rear section of
the node (the side without the
Brill logo). Gently press in the
four nuts so that they are in-
serted properly and do not fall
out of the recesses when the
node is turned over (Fig. E).
Turn the mower so that the
rollers rest on the ground.
Prepare the top and middle
sections of the guide handle
so that the sections of the
handle overlap as shown in
the assembly diagram (Fig. F).
Hold the rear section of the
node so that the grass catcher
holder (28) faces upwards
and guide the cable through
Attention ! To prevent injury,
A
the PowerAccu must only
be used as a power source for
24-Volt tools manufactured by
Brill.
Only the Power Accu 24 PA,
A
Brill article no. 65028, in-
cluded in the packaging, can be
used with the hand lawnmower.
the cable duct on the left side
of the node (Fig. G) (viewed
from below. Pay attention to
the length of the cable!).
Now insert both sections of
the handle according to the
recesses (Fig. H).
Attach the front section of the
node to the rear section of
the node. Make sure that you
hear the clip lock snap into
place and screw together both
parts of the node using the
bolts provided (Fig. I/K).
3. Now attach the middle and
top sections of the guide
handle using the bolts and
wing nuts provided (Fig. L/M).
Warning! The cable must
not hang down near the
cutting cylinder.
5.3. Setting the cutting height
(fig. N/O)
Warning ! To prevent injury,
A
never set the cutting height
when the motor is running.
Set the cutting height on the
Accu Hand Lawnmower as
follows:
1. Stand the Hand Lawnmower
on a flat, solid surface.
2. Position yourself in front of
the cutting height scale of
the Accu Hand Lawnmower
(fig. N).
US
9
Publicité
Table des Matières
