Using The Machine; Cutting Height - Stiga PARK 110 COMBI PRO Mode D'emploi

6. Tension the belt as follows.
Park 2WD:
Tension the belt with the belt idler. The belt
idler should be on the left side of the belt
viewed from the driver's position. See fig. 10.
Park 4WD:
Grip the belt tensioner's lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig.9.
7. Suspend the unit in the implement lifter. See fig.
6.
8. Screw the arms into each other. See fig. 5.
9. Perform the cutting deck basic setting:
On machines with 17" wheels: Install the wash-
ers and the pins in the top hole. See fig. 2.
On machines with 16" wheels: Install the wash-
ers and the pins in the middle hole. See fig. 2.
10.If the deck has electrical cutting height adjust-
ment, connect the cable to the machine's front
right socket. See fig. 7.
3.2 MACHINES WITH QUICK CON-
NECTIONS
Example of quick connections, see fig. 8.
1. Place the deck in position in front of the ma-
chine.
2. Check that the quick connections are fitted to
the machine according to their supplied sepa-
rate instruction.
3. Remove the pins and the washers on both sides.
See fig. 2.
4. Check that the deck arms are screwed into place
in the quick connections. If this is not the case,
screw them into place. See fig. 8.
5. Set the quick connections in their rear positions.
See their supplied separate instruction.
6. Suspend the cutting deck in the implement lift-
er. See fig. 6.
7. If the deck has electrical cutting height adjust-
ment, connect the cable to the machine's front
right socket. See fig. 7.
8. Install the belt as Monte la correa con arreglo al
3.2.1 / 3.2.1.
3.2.1 Belt, 4WD
The cutting deck's rear section should rest on the
floor (it should not be lifted or secured).
Install the belt as follows:
1. Set the maximum cutting height.
2. Locate the belt around the machine's belt pulley
(9:M).
3. Tension the belt as follows.
Grip the belt tensioner's lever with your left
hand. Pull the lever and apply the tensioner to
the outside of the belt with your right hand. See
fig. 9.
ENGLISH
4. Lift up and secure the rear section of the cutting
deck.
On machines with 17" wheels: Install the wash-
ers and the pins in the top hole. See fig. 2.
On machines with 16" wheels: Install the wash-
ers and the pins in the middle hole. See fig. 2.
5. Set the quick connections to their front posi-
tions, see separate instructions.
3.2.2 Belt, 2WD
The cutting deck's rear section should rest on the
floor (it should not be lifted or secured).
Install the belt as follows:
1. Set the maximum cutting height.
2. Locate the belt around the machine's belt pul-
ley.
3. Tension the belt with the belt idler. The belt
idler should be on the left side of the belt
viewed from the driver's position. See fig. 10.
4. Lift up and secure the rear section of the cutting
deck.
On machines with 17" wheels: Install the wash-
ers and the pins in the top hole. See fig. 2.
On machines with 16" wheels: Install the wash-
ers and the pins in the middle hole. See fig. 2.
5. Set the quick connections to their front posi-
tions, see separate instructions.
3.3 TYRE PRESSURE
Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).
3.4 BASIC SETTING
In order for the cutting deck to cut optimally, the
correct basic setting is required. The deck is in the
basic setting when its rear edge is 5 mm above its
front edge. This means that the deck is inclined
forwards.

4 USING THE MACHINE

Check that the grass that is to be cut is
completely free of foreign objects such
as stones etc.

4.1 CUTTING HEIGHT

The best cutting results are achieved when the
when the top third of the grass is cut off. I.e. 2/3 of
the length of the grass remains. See fig. 11.
If the grass is long and has to be cut significantly,
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn
surface is uneven. This would entail a risk of the
blades being damaged against the surface and the
lawn's top layer of soil being removed.
EN
27