Introductory Comment; General Rules Of Safety; Transfer; Storage And Disposal - ADIATEK diamond 85 Manuel D'emploi Et Entretien

INTRODUCTORY COMMENT

Thank you for having chosen our machine. This
floor cleaning machine is used for the industrial
and civil cleaning and is able to clean any type of
floor. During its advance movement, the combined
action of the brushes and the detergent solution
removes the dirt which is aspirated through the
rear suction assembly, giving a perfectly dry
surface.
The machine must be used only for such purpose. It
gives the best performance if it is used correctly
and maintained in perfect efficiency. We therefore
ask you to read this instruction booklet carefully
whenever difficulties arise in the course of the
machine's use. In case of need, we ask you to
contact our service department for all advice and
servicing as may prove necessary.

GENERAL RULES OF SAFETY

The rules below have to be followed carefully in
order to avoid injury to the operator and damage
to the machine.
− Read the labels carefully on the machine. Do not
cover them for any reason and replace them
immediately if damaged.
− ATTENTION:
The machine
exclusively by authorized staff that have been
instructed on its correct and proper use.
− ATTENTION: Do not use the machine on areas
having a higher gradient than the one stated on
the number plate.
− ATTENTION: The machine is not to be used by
persons, children included, with reduced physical,
sensorial or mental capabilities, or with lack of
experience or knowledge, unless they could
benefit, through the intermediation of a
responsible person for their safety, by a
supervision or instructions concerning to its use.
− During the operation of the machine, pay
attention to other people and especially to the
children.
− Children shall not play with the machine.
− Children
cannot carry out
maintenance of the machine.

TRANSFER

− Do not strike shelvings or scaffoldings where
there is danger of falling objects.
− Leaving the machine in parking position, take off
the key and act upon the parking brake.
− Do not use the machine as a means of transport.
− Adapt the working speed to the adhesion
conditions: particularly, slow down before
narrow curves have to be faced.

STORAGE AND DISPOSAL

− Storage temperature: between 0°C and +55°C
(32°F and 131°F).
− Perfect operating temperature: between 0°C and
+40°C (32°F and 104°F).
− The humidity should not exceed 95%.
− Provide for the scrapping of the material of
normal wear (brushes, squeegee blades etc.)
following strictly the respective rules.
When your machine has to stop activity, provide for
the appropriate waste disposal of its materials,
especially oils, batteries and electronic components,
and considering that the machine itself has been,
where possible, constructed using
materials.

CORRECT USE

− Do not use the machine on surfaces covered with
inflammable liquids or dusts (for example
hydrocarbons, ashes or soot).
− In case of fire, use a powder based fire-
extinguisher. Do not use water.
− Do not use the machine in explosive atmosphere.
− The machine has to carry out simultaneously the
operations of washing and drying. Different
operations must be carried out in restricted areas
prohibited to non-authorized personnel and the
operator has to wear suitable shoes.
− Signal the areas of moist floors with suitable
signs.
− Do not mix different detergents, avoiding
harmful odours.
− Avoid brushes operation when the machine is
standing still in order to prevent floor damages.

MAINTENANCE

− If the machine does not work properly, check by
conducting simple maintenance procedures.
Otherwise, as for technical advice from an
authorized assistance centre.
− For any cleaning and/or maintenance operation
take off the power supply from the machine.
− Where parts are required, ask for ORIGINAL spare
parts from the distributor and/or from an
authorized dealer.
− Use only ORIGINAL brushes indicated in the
paragraph "RECOMMENDED BRUSHES".
− Do not take off the protections which require
the use of tools for their removal.
− Do not wash the machine with direct water jets
or with high water pressure nor with corrosive
material.
− Every 200 working hours have a machine check
by an authorized service department.
− Before using the machine, check that all panels
and coverings are in their position as indicated in
this use and maintenance catalogue.
− Restore all electrical connections after any
maintenance operation.

BEFORE USE

HANDLING OF THE PACKED MACHINE

must be used The machine is supplied with suitable packing
foreseen for fork lift truck handling.
The total weight is:
version 85: 620kg (1367lbs.)
version 100: 650kg (1433lbs.)
version 100 with side brush: 690kg (1521lbs.)
Packing dimensions:
Base: 213 cm x 115 cm (84"x45")
Height: 165 cm (65")
Do not place any packings on top.

UNPACKING OF THE MACHINE

1. Remove the external packing.
2. Move the machine backwards, as indicated in the
cleaning and figure, avoiding heavy contacts to mechanical
parts.
3. Keep the pallet for eventual transport.

ACCESS TO THE BATTERY COMPARTMENT

1. Bring the machine on a levelled surface.
2. Rotate the seat platform forward up to the
blocking of the support.
3. Having finished any intervention, to close the
battery compartment, after having released the
support, reposition the seat platform.
recyclable
BATTERY INSTALLATION AND SETTING OF THE
BATTERY TYPE
The machine is equipped either with batteries in
serial connection
assembled together and connected in series for a
total of 36 Volt, placed in its appropriate
compartment under the seat platform and must be
handled using suitable lifting equipment (due to
weight, considering the type of batteries chosen,
and coupling system).
or elements of DIN-type
16
The batteries must be in accordance with CEI 21-5
Norms.
The machine and its battery check card foresee the
use of traditional lead batteries.
CHECK THE SETTING OF THE CHECK CARD (see
under paragraph "BATTERIES
INDICATOR").
In case of GEL batteries installation, it is necessary
to set the check card. Please contact the authorized
technical assistance.
Strictly follow manufacturer/distributor indications
for the maintenance and recharge of the batteries.
All installation and maintenance operations must
be executed by specialized staff, using suitable
protection accessories.
For batteries installation it is necessary to reach the
battery compartment as indicated under paragraph
"ACCESS TO THE BATTERY COMPARTMENT".
1. Place the batteries in its compartment.
2. Connect the terminals,
polarities, avoiding contact with other parts
that could create short circuit.

ASSEMBLING OF THE ROLLBAR

For packing reasons the support of the blinking
light is supplied disassembled.
Proceed as follows:
1. Take off the four fixing screws (1) from the
rollbar.
2. Place the rollbar into their seats (2) on the tank.
3. Fasten the screws passing them in the same
order in their holes foreseen on the support.
4. Complete the assembly
connectors (3) to supply the blinking light.

BATTERY RECHARGER

Make sure that the battery recharger is suitable for
the installed batteries both for their capacities and
type (lead/acid or GEL and equivalent).
In the plastic bag containing the use and
maintenance you will find the coupling connector
for the recharger. It must be assembled onto the
cables of your recharger, following the instructions
given by the manufacturer.

BATTERIES RECHARGING

1. Plug the connector (3) of the battery recharger
into the battery connector.
2. Proceed for the recharging.
Never charge a GEL battery with a non suitable
recharger. Strictly follow the
supplied by the batteries
manufacturer.
CHARGE LEVEL
respecting the
connecting the
instructions
and recharger