Introductory Comment; General Rules Of Security; Symbology - ADIATEK ruby 50e Emploi Et Entretien

GB

INTRODUCTORY COMMENT

Thank you for having chosen our machine. This floor
cleaning machine is used for the industrial and civil
cleaning, suitable for hard and not very rough floor-
ings. During its advance movement, the combined
action of the brush and the detergent solution re-
moves the dirt which is aspirated through the rear
suction assembly, giving a perfectly dry surface.
The machine must be used only for such purpose. It
gives the best performance if it is used correctly and
maintained in perfect efficiency. We therefore ask
you to read this instruction booklet carefully when-
ever difficulties arise in the course of the machine's
use.
In case of need, we ask you to contact our service
department for all advice and servicing as may prove
necessary.

GENERAL RULES OF SECURITY

The rules below have to be followed carefully in or-
der to avoid damages to the operator and to the ma-
chine.
- Read the labels carefully on the machine. Do not
cover them for any reason and replace them imme-
diately if damaged.
- WARNING: The machine must be used exclusively
by authorized staff that has been instructed for its
use.
- The machine is not to be used by persons, children
included, with reduced physical, sensorial or mental
capabilities, or with lack of experience or knowledge,
unless they could benefit, through the intermedia-
tion of a responsible person for their safety, by a su-
pervision or instructions referring to its use.
- During the working of the machine, pay attention
to other people and especially to the children.
- Do not mix different detergents, avoiding harmful
odours.
- Do not place any liquid containers onto the ma-
chine.
- Storage temperature: between -25°C and +55°C.
- Perfect operating temperature: between 0°C and
40°C.
- The humidity should be between 30 and 95%.
- Do not use the machine in explosive atmosphere.
- Do not use the machine as a means of transport.
- Do not use acid solutions which could damage the
machine and/or the persons.
- The socket for the power supply must be equipped
with a standard earthing (ground) system.
- WARNING: Do not touch or pass over the mains
cable while the brush is operating.
- Do not damage the mains cable with squashings,
bendings or stressings.
- Check the integrity of the mains cable. If during
working a damage is noticed, stop the machine im-
mediately and take off the plug from the mains
socket. Replace with the special cable available at
the authorized center of the technical assistance.
- In bad mains conditions, the machine could cause
transitory voltage drops.
- Avoid working with the brush when the machine
stands still, in order to prevent floor damages.
- WARNING: Do not use the machine on surfaces
covered with inflammable liquids or dusts (for ex-
ample hydrocarbons, ashes or soot).
- In case of fire, use a powder fire-extinguisher.
Do not use water.
- Do not strike shelvings or scaffoldings, where there
is danger of falling objects.
- Adapt the working speed to the adhesion condi-
tions.
- WARNING: Do not use the machine on areas hav-
ing a higher gradient than the one stated on the
number plate.
- The machine has to carry out simultaneously the
operations of washing and drying. Different opera-
tions must be carried out in restricted areas prohib-
ited to non-authorized personnel.
- Signal the areas of moist floors with suitable signs.
- If the machine does not work properly, check by
conducting simple maintenance procedures. Other-
wise, ask for technical advice to an authorized assis-
tance centre.
- Where parts are required, ask for ORIGINAL spare
parts to the distributor and/or to an authorized
dealer.
- WARNING: Use only ORIGINAL brushes indicated in
the paragraph "RECOMMENDED BRUSHES".
- For any cleaning and/or maintenance operation
take off the power supply from the machine.
- Do not take off the protections which require the
use of tools to be removed.
- Do not wash the machine with direct water jets or
with high water pressure nor with corrosive material.
- Every 200 working hours have a machine check
through an authorized service department.
- In order to avoid scales on the solution tank filter,
do not fill the detergent solution many hours before
the machines' use.
- Before using the machine, check that all panels
and coverings are in their position as indicated in
this use and maintenance catalogue.
- Be sure the recovery tank is empty before remov-
ing it.
- Restore all electrical connections after any mainte-
nance operation.
- Provide for the scrapping of the material of normal
wear following strictly the respective rules.
- When your machine has to stop activity, provide
for the appropriate waste disposal of its materials,
especially oils and electronic components, and con-
sidering that the machine itself has been, where pos-
sible, constructed using recyclable materials.

SYMBOLOGY

Symbol denoting the solution
valve.
Indicates the solution valve knob
and the signal lamp of the
solenoid valve.
Symbol denoting the brush.
Indicates the switch of the brush
motor.
Symbol denoting the suction
motor.
Indicates the switch of the suction
motor.
Symbol denoting up – down of
the squeegee.
Indicates the squeegee lever.
Symbol denoting the flash.
Indicates the signal lamp for
presence of the mains tension on
the machine.
Indication of the maximum
temperature of the solution
detergent.
It is placed near the charging
hole of the solution tank.
16
GB
Symbol denoting the squeegee
adjustment.
Symbol denoting the crossed
bin. Indicates that at the end of
its activity, the machine has to
be disposed conforming to the
laws in force.
Symbol denoting the open book.
Indicates that the operator has
to read the manual before the
use of the machine.
Warning symbol.
Read carefully the sections
marked with this symbol, for the
security of both the operator
and the machine.