Changing The Password; Parameter Setting - SOMFY SO 1841210 Manuel D'installation Et D'utilisation

GSM Receiver

8. Changing the password

The password must contain 6 digits. The default password is 123456.
From a telephone stored in the receiver memory, send the following SMS to the SIM card number:
#PWdpassword#CaPnew password#CaPnew password
Password
123456 by default
Keep this password somewhere safe.

ParamEtEr sEttiNG

the code to be sent must Not contain spaces and must be in CaPital lEttErs. Each time an SMS is sent, the receiver sends the sender a response
message.
Checking the GSM signal
Code to be sent
#PWdpassword#CsQ?
Excellent signal =31
Good signal =16
Low signal =12
Very low signal <12. If the signal is below 12, find a new location to place the card or switch to another telephone operator offering a better signal in the zone in question.
If no response SMS is received, the zone is probably not covered by the telephone operator's GSM signal.
Enter a new telephone number in the memory (maximum of 99 numbers).
The telephone number must contain a maximum of 10 digits (no country code).
Note: some telephone operators require the number to be saved with the last 9 or 8 digits.
Code to be sent
#PWdpassword#Whlposition in the memory=telephone
number
In the example, the telephone 0123456789 is entered in position 1, telephone number 9876543210 is entered in position 2 and telephone number xxxxxxxxxx is entered in
position 99.
Change the password for managing the various programming functions. The password must contain 6 digits.
The default password is 123456. All the examples in this manual have 123456 as the password.
Code to be sent
#PWdpassword#CaPnew password#CaPnew password #PWd123456#CaP321654 #CaP321654
In this example, the password is changed to 321654.
The activation time for the OUT1 output is configured from 1 to 99 seconds (default is 1s) when the receiver receives a call from a memorised telephone number.
Code to be sent
#PWdpassword#Gotdefault activation seconds for
output out1
In the example, the OUT1 output is activated for 5 seconds each time the receiver receives a call from a memorised number.
Check the telephone number memorised in a position in the memory.
Code to be sent
#PWdpassword#Whlposition in the memory?
In the example, we are querying position 02 in the memory.
Delete a telephone number in the memory.
Code to be sent
#PWdpassword#Whlposition in the memoryd
In the example, the telephone number in position 02 in the memory is deleted.
Note: to delete the number memorised in position 99, send an SMS as in the example: #PWd123456#Whl99d=0000000000
Copyright © 2014 Somfy SAS. All rights reserved
New 6-digit New 6-digit
password password
Example of sms to be sent
#PWd123456#CsQ?
memorising a new telephone number in the receiver memory
Example of sms to be sent
#PWd123456#Whl01=0123456789
#PWd123456#Whl02=9876543210
...................................................
#PWd123456#Whl99=xxxxxxxxxx
Example of sms to be sent
out1 output activation time
Example of sms to be sent
#PWd123456#Got05
Checking which telephone number is memorised in a specific position in the memory
Example of sms to be sent
#PWd123456#Whl02?
deleting a number in the memory
Example of sms to be sent
#PWd123456#Whl02d
deleting all the numbers in the memory
Example of SMS to be sent:
In this example, the new password saved is 456789.
Quality of the Gsm signal
Changing the password
#PWd123456#CaP456789#CaP456789
Example of sms received
CsQ=<23>
Example of sms received
Whl01:0123456789
Whl02:9876543210
....................................
Whl99:xxxxxxxxxx
Example of sms received
CaP:321654
Example of sms received
Got:05
Example of sms received
Whl02:9876543210
Example of sms received
Whl02-oK
3